Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
On nRF54L15 (NCS v3.1.0), we are using the SAADC with ADC_GAIN_1_4 and ADC_REF_INTERNAL at 14-bit resolution to measure an analog voltage on AIN5. The driver sets ref_internal...
Hi.
I am attempting to obtain SIG certification.
I am using ncs v3.1.1 with nRF52833.
Based on the link below,
https://docs.nordicsemi.com/bundle/comp_matrix_nrf52833...
Dear NORDIC engineers, excuse me. I would like to inquire about the Settings of NRF54LM20 APPPROTECT. I have modified APPROTECT[n].protect0 and APPROTECT[n].protect1 to 0x5A5A5A5A...
I am trying to use the nRF54L15 DK board to flash a Fanstel BM15M module.
Fanstel BM15M module link: Fanstel BM15M Module
I am using the nRF54L15 DK board with the external...
Hi --
We are in the process of setting up to flash a few hundred devices for our internal testing. We can currently flash to our board using nrfjprog either directly from...
I have a nRF9151 dev kit for evaluation that I am following official guide to get up and running using the asset tracker v2 program. I can flash the firmware but I cannot...
I want to expand the flash allocated to mcuboot on the NRF desktop, but it failed to start after compilation
The following is a flash layout that can be successfully launched...
It seems there might be a small issue with the TF-M GPIO MCU-select IOCTL plumbing on nRF54L — specifically when a non-secure app tries to configure sQSPI GPIOs (and presumably...
I have successfully completed the one script install of Zephyr on RPI and can fully develop Nordic nrf52832/nrf52840. I assume all other supported boards within Zephyr can...
I'm trying to advertise an isochronous IN endpoint with wMaxPacketSize = 768 bytes (8 channels × 48 kHz × 16-bit audio, 1 ms polling). USB init fails at usbd_init with Failed...
Hello! We are in the middle of an upgrade to 3.2.1, and we encounter the following issue using SB_CONFIG_MCUBOOT_MODE_SWAP_WITHOUT_SCRATCH, SB_CONFIG_MCUBOOT_MODE_SWAP_USING_MOVE...
I measured the power consumption of the BLE RX using the nRF54L15.(nRF54L15-DK v1.0.0) 3.0V operation apps: scan_adv (delete advertising) west build -b nrf54l15dk/nrf54l15...
