Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
I will be deploying my nRF51822-powered devices into the field and the end user will not be able to have any physical access to, for example, power cycle the board. I need...
Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I'm running Windows 10 and loaded pc-nrfconnect-ble-231-master from GitHub,
Per the README I npm installed windows-build-tools, then npm install.
I got some warnings about...
I am using nrf52832 dev board . I have used the example code of ble_app_beacon code . I am able to send my data through the beacon. But while using nrfconnect app, the scanning...
HI,
I've been using the Nordic Command Line Tools to do the following:
program an example hex file to the SoC
read the code, ram, and uicr registers and save to file...
Hello.
My question concerns UUID.
Exactly where does it come from?
Can I generate this UUID for my own application ( https://www.uuidgenerator.net/ ) or maybe it is...
Working on a migrating RF test firmware that was working on 52832 using SPI to AT86RF233(for 802.15.4). Was able to exercise PHY with that setup to send specific packet with...
Hello, Nordic!
I am wondering about PCB reference design for AoA multi antenna locator based on 52811.
Could you provide it before releasing software supporting this functionality...
Hi. I looked through all the examples in the 15.20 and 15.30 SDK and could not find even one project for SES with it's new linker as an example. all the examples use the old...
To be able to SMS we need the SMSC number stored in the SIM card.
I did not find an AT command to read this, so I gues we need to use the +CSIM or +CRSM?
Regards,
F...
I am using nrf52832 for button less DFU. DFU is working fine when CONFIG_NFCT_PINS_AS_GPIOS is not added in applicaton. When added seems like code is getting reset at bootloader...
I have problems compiling code with modem info support on. My basic problem, I want to establish which modem FW version I am running on.
I added
MODEM_INFO_CONFIG=y
...
We successfully built the mesh bootloader, but want to get RTT working with the bootloader logs inside SEGGER.
We were following this two posts post1 post2 to achieve our...
Hello guys.
I just donwload new version of SDK 1.0.0 for NRF9160 and try run mqtt_simple demo. I didnt change nothing there and there is problem.
I have the follow log...
Hello,
Currently my beaconing application draws approximately 10uA @ 1000ms advertising interval. I am having trouble getting the chip into system power off mode so the...
Hi,
We would like to upgrade an existing product (Bluetooth SIG registered) on the market to the newest release of SoftDevice. Do we need to re-register at Bluetooth SIG...
Hi,
I'm working on a bootloader based on the "secure_bootloader/pca10056_ble" example. Everything works fine until I send the new application binaries (.zip file) and the...
