I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi,
I have seen that the pin for nRESET is selected on the NRF_UICR->PSELRESET register. I know that it cannot be modified from 0.21 on the 52832.
Can it be modified on...
Hi guys,
I am trying to figure out how to send the sensed data (temperature value) from the LPN node to the server node in the BLE mesh network. I have already found this...
I am using the nrf5340PDK and i am trying to have P1.04 trigger an interrupt on a high to low transition.
attached is my overlay file and my main.c to initialize the GPIO...
I made a code based on ble_app_uart_c which connects to a peripheral and once connected it can write or read data.
The code is supporting BLE4 (1M) and BLE5 (Long Range...
Dear Concern,
we have tried to configure the accelerometer LSM6DSO module through SPI interface using NRF52xx DK board. External Module was not configured properly...
Since the Online Power Profiler only supports 1M PHY, does a static power profile for coded PHY exist that shows the current levels for the full advertising length? I'd like...
hi
nRF5 SDK for Thread and Zigbee v4.1.0
need to build a simple sensor with analog input .
Referring to the simple sensor (binary input ), I did make a ZED simple binary...
i made a mesh network using cli ftd uart example and transfer data using udp portal
there comes a need for me to indicate reset command through switch and send reset command...
I have 2 devices connected, working in notification mode. Using the nRF Sniffer for Bluetooth LE I was able to check all the messages that are exchanged. When in close proximity...
Hi, We have chosen to put our project and "custom board" outside of the NCS-directory. And since the newer revisions of SES, the "Open nRF Connect SDK Project" dialog window...
Hi,
On the P eripheral , after establishing a connection with the Central , start the timer to send data to the Central (the timer interval is set to 500ms and stop after...
I'm trying to get Thingy91 works under either Mac OS or Linux. Neither of Programmer nor LTE Link Monitor doesn't work. Programmer complains about that device is not in MCU...
Hi everyone,
I'm reading the documentation about USBD and I have some questions about it.
1) What's the EasyDMA? Maybe I understand what it is but I am not sure so I ask...
