Hi,
We are using the ble_app_uart example in evaluation board to read data from some sensors and send it to the nRF UART V2.0 in Android 4.4. Every 20 ms I am trying to...
I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi Team,
We are working on project where we are trying to encrypt the advertisement data (non-connectable) using our own defined keys.
currently I have been through the...
Using Segger with PCA10056 as a debugger connected to a pcb with a NRF52840 on it. Been working fine and I tried building open bootloader and programmed it. I see the device...
Hello,
I am a newby to the nRF5340 and Zephyr and I am stuck. I would like to know how to map physical pins to a particular UARTE.
I have read in the user manual OPS_v0...
Hello,
Currently developing a system based around the NRF9160 running Zephyr. My application is threaded and i would like to run the thread_analyzer. I got this working...
Hello,
I want to hide the BLE(RF signals) completely soon after updating the configuration in my application and whenever I need to update the config I should be able to...
Hi, I'm reading an ADC channel connected to large capacitors. I do the read when charging is off so no ripple. The caps are large (super-caps) so hold well enough to show...
Hey. If the device is repeatedly flashed without turning off its power (it does not matter if I program it through SES or nRFgo), it may start to malfunction or slow down...
Hello
I would like to use three PWM to output multiple sounds with one buzzer.
First of all, I am testing using two PWM. There is no problem using only one PWM, but there...
Hi, I'm currently using TAIYO YUDEN's EYSLCNZWW (nRF52810) and We are developing a device like a pulse oximeter.
I would like to change SAADC_SAMPLE_RATE from 400ms to 100ms...
Hi, after using the nRF SDK examples with SES for some time now, I decided to go with a project from scratch but for some strange reason the directory where I keep the nRF...
Hi everyone,
I am using the custom nRF52840 module provided by Raytac. I integrated into my evaluation board and I flash it using SWD and JLink debugger. My problem is that...
I have DFU code base working. It consists of a thin layer of our code, and majority is from Bootloader component from SDK v17.
I started with DFU OTA, and then incorporated...
Hello,
I am trying to reproduce the Mesh Light Switch demo at home now, with my own dev equipment and have hit some problems I did not expect -
Problem:
nRF52840 Dongle...
