E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
I have been trying to understand and get the “ble_app_template” running this weekend, but I keep running into errors. For example in
static void sys_evt_dispatch(uint32_t...
Based on the nRFUart demo, I added a masterEmulator.DiscoverServices() block before the DiscoverPipes() block in a very similar manner. Purposed is to be able to get more...
Hi,
There is much talking about the "large data transfer" over BLE, the l2cap channel being the best option for the moment.
However, does anyone know the datarate achievable...
NRF24AP2 with MSp430F149 . ASYNC 9600 N 8 1
step 1 : reset NRF24AP2 with reset pin , and received a pulsing signal through RTS pin
step 2: send a char (0x4A) to NRF24AP2...
Hi guys,
I am using the gcc setup to program my boards. However for flashing the softdevice I use nrfgoStudio. SO I downloaded the hex file and fashed the siftdevice. But...
In our application build with SDK 2.7.0 on a NRF52840 chip, we get an assert if we update the TX_Power for the connections.
If the bluetooth has made connection, we update...
Hey everyone!
I’m working on a project using Zephyr with an nRF5340 board and trying to configure UART1 completely from scratch. Most tutorials I’ve found only cover UART0...
Dear Nordic Support Team,
I am working with the nRF52840 and need to configure the SPI peripheral in Zephyr to operate without DMA.
I’ve encountered a few problems:
...
I am able to update the app core successfully from an external flash partition via the `mcumgr` desktop tool. However, this is not working for the net core.
It successfully...
I would like to create a thread based sensor and use Apple/Amazon/Google smarthome hubs as the OTBR. How do I commission a thread device (not a matter device) to these hubs...
Hello,
I'm working with Zephyr and using MCUBOOT as bootloader.
Due to HW design I have to set and hold a gpio as fast as possible when the application boots (to prevent...
Hello,
We're seeing an error that only happens after a cold reboot (unplugging the battery and replugging it) and it happens inside the bootloader while trying to open the...
Dear all:
I used this command to build light switch for 5340DK:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp nrf...
Kconfig failed: [Errno 22] Invalid argument: 'c:/users/user/zephyr/kconfig"' is an error that appeared this morning. What is supposed to be in the Kconfig file. I have been...
I can't remember where I found it now, there was a file somewhere that listed all the files in a project. It had
absolute paths which filled me with dread as it means a...
Hi
I am working on a custom board and have hit an issue with the software part. When the nrf_modem_lib_init function is invoked, it always ends with a timeout (errno ...
Got a Thingy91 (not the x model) that doesn't show up as anything when connected to a PC by USB, except when in bootloader mode, by pressing SW4 (no reaction with SW3) when...
I read other similar issues on this forum but they haven't helped solve my problem. I started with the peripheral_uart example project. Development and execution on the target...
Sorry for long sentence. The nRF5340 document describes about the Reset. This chip set have the POR. so, if POR function work, I don't need to use the PIN reset. because POR...
I have configured my application according to the Throughput example. The prj.conf file inside the sysbuild\ipc_radio folder is not being considered in the build. As a result...
