I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi,
I have 3 Devices that constantly broadcast their position to each other so the other can adjust the position each other. they act like master and slave but ther are...
I'm trying to get the most performance per mA out of my nRF52, for test purposes I've used the nrfx libraries to communicate to the peripherals but I want to make my own....
Dear Nordic
my SOFT DFU fail when I init the WDT, but I have feeddog and disable the WDT, like below:
static bool app_shutdown_handler(nrf_pwr_mgmt_evt_t event) { switch...
When access_model_subscription_list_dealloc() is called the entry is memset to 0 and the ACCESS_INTERNAL_STATE_INVALIDATED flag is set.
The function access_model_subscription_list_alloc...
Hi all,
I have a nRF52 DK (PCA10040 V1.2.1), and I want to learn how to develop on macOS.
I read from this link , and I got following information.
But I cannot know...
Hi,
I use The Texas Instrument software "SmartRF Packet Sniffer Bluetooth Low Energy" to catch the communication between my peripheral build with nRF52832 and Zwift (software...
Hello
I am trying to configure your TWIS (not using the SDK) and have run into the problem that the TWI master cannot pull the SDA and SCL line low. So, the communication...
52832's PDM function. After initialization, call the nrf_pdm_enable function, and then call the nrfx_pdm_start function. NRFX_PDM_ENABLED is set to 1. But the clock pin always...
I am evaluating the NRF52810 (using the PCA10040 dev kit), and I am having a hard time getting down to the described power consumption of the chips. I am using the power profiler...
i have done ble_app_template writing values from nrf app connect, in that i have send only integer values from nrf app connect
now i want to write float values from nrf...
Hello,
I have enabled the watchdog timer in nrf52810 with below code
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Pause << WDT_CONFIG_HALT_Pos) | ( WDT_CONFIG_SLEEP_Pause << WDT_CONFIG_SLEEP_Pos...
Hi,
I have some problem with experimental_lpn project from sdk_for_mesh. (Today I tried both sdk 3.2 and 4.0)
Code loads and starts ok on my PCA10040.
After first steps...
