I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hello,
I am testing the capabilities of Thingy:91, the first day I could see data in cloud (temperature and other sensors + GPS).
Today usage of SIM card grows up but...
Hello,
I'm trying to setup a new project and start experimenting with the nRF51 series. I'm a little confused about the needed files I have to add on the project to get...
Hi:
SDK version: SDK 13.0
MCU: nrf52832
For the purpose of saving power, the peripheral disconnect the BLE connection in the program when there is no data transmission...
Hello,
I am using nRF52832 EVM board with SDK 15.3.0 in SEGGER studio IDE, win 10.
When I am implementing sd_nvic_SystemReset(); in my code, that time i am not able to...
I have a custom board based on QIAA Reference Layout 1.1 Variant 6.
The application is built with Zephyr without bootloader and is placed directly on address 0x0.
When...
Hi, I'm designing nRF52832 custom board, on 'single side' pcb.
To make VDD and GND lines connect, I used 4 jumpers, which have 0 ohms.
I designed with nRF52832-QFAB reference...
I used the ble_app_uart for pca10040e successfully on the DK52, now I'm trying to port that project onto actual nRF52810 chip.
This is my build configuration on SES (Segger...
Hello Nordic Support Team,
The question I have is simple.
Can I use the pc-ble-driver with the ble_connectivity_s140_usb_hci example found in SDK15.3.0?
If not why?...
Is there any public documentation on the LTE Modem hardware API for the nRF9160?
I'm interested in porting an embedded operating system written in Rust to the nRF9160 and...
Hi,
I am using ncs 1.0.0 in nRF9160.
I have enabled UART 2 interrupt during initialization of the uart as below and it works fine.
To reduce the power consumption...
Hi,
Using the Thingy app on my iPhone works fine.
However, I would like using my iPhone as a gateway (thingy:52 -> iPhone (BLE -> Internet) -> nrFCloud. I installed the...
Hi,
I'm migrating a project from SDK 14.2 to 15.3 and I wanted to use the generic and "full" sdk_config.h located in config/nrf52840/config/.
The documentation says...
Hi everyone, I would like to confirm if this is a bug.
Per the comment, it seems that the intent of the code is to reject an attempted SoftDevice update.
However, this...
