Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Recently, we started developing our new project using the nRF52832 as our controller.
We are using Segger Embedded Studio (5.42a) as our IDE.
My question is: Are there...
I work for nRF52833 on NCS2.8.0.
I try to set SB_CONFIG_MCUBOOT_COMPRESSED_IMAGE_SUPPORT=y for sysbuild.
build error is occured.
Maybe there is not enough RAM for mcuboot...
My NCS version is 2.6.1, and the modem firmware version is 1.3.6
I found that delta upgrade often fails when testing the firmware of FOTA upgrade modem for 9160. Currently...
Hello. How can I monitor that SoftDevice is working properly? I am trying to monitor using Radio notification, but RADIO Active does not guarantee that the SoftDevice is working...
Hi ,
I am running "Cellular IoT Fundamentals". In Lesson 4, Exercise 1, has MQTT communication. Everything went well up to the point where I have to PUBLISH from MQTT Explorer...
Hello,
I'm new to pretty much all of this, but I'll do my best to explain my issue. As the title says, I'm currently trying to get a LSM6DSO sensor to work with the NRF52832...
Is there a way to avoid duplicate board targets if I have the same repository in two different places on my machine?
Or some way to ignore a workspace path so they're...
I am working on a project using ncs 2.2.0 on the nRF52833DK.
I have a very simple requirement, which is to save an id-data pair in Non-Volatile Storage and be able to change...
I made an example based on the NVS sample code (Connect SDK 2.2.0) which simply reads a value from the storage partition if it exists, then updates it if either it's different...
We have a system with a central device and a peripheral both based on nrf5340. The central device is also a Broadcast source and the peripheral is also a Broadcast sink in...
I’m working with the Audio Application (from the Nordic sample program) on an nRF5340 Audio DK as a gateway, and a custom board with an nRF5340 as a headset. The custom headset...
Hi, I'm running the fatfs sample using an Actinius Icarus board (nrf9160) and a microSD card, connected via SPI. The original sample works as it should (it mounts and opens...
Before setting `CONFIG_USERSPACE=y`, my image size is ~680KB. After setting it, it overflows my partition by ~60KB. The partition size is ~840KB, meaning userspace has added...
Hi,
I am testing the BLE beacon sample on the NRF54L15 PDK, and it was successful as I was able to detect the beacon using the NRF Connect scanner. However, when monitoring...
