Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hello team,
I am looking this API "zb_secur_ke_whitelist_add" in the nRF5 SDK v16.0.0., nrf5_sdk_for_thread_and_zigbee_v4.2.0_af27f76.zip but not able to find in the library...
I need to develop the code for RTC configuration without using nrf_drv_rtc_* , hence I started using zephyr device tree approach . Below is my code .
#include <stdio.h...
Hello,
I recently purchased a Nordic Thingy 91 device, and I have been working on it for a few weeks. I am currently experiencing two major issues with the kit that are...
Hi,
I have a board which is nrf9151 with nrf52840 as BLE controller connected via hci_lpuart. This works fine so far, I am able to do simple AT commands as well as doing...
when I try to add a build config, i can only see a blank page for build configs.
but if i click on another project's build config which is already created, i can see the...
Hi,
I'm troubling using the retention module of Zephyr with NCS 2.6.1 on an NRF52840. I've read the Retention System Documentation of Zephyr but it is not working for me...
Folks,
Am running VSC 1.95.1 on Mageia Linux.
I have a 52833 board that I have working in that I can write to and read from custom BLE characteristics and send data out...
Hi
I'm setting up an OpenThread network and am trying to use the nRF Thread Topology Monitor to visualize the network for debugging purposes. However, no OT devices appear...
According the AT command documentation, reading the device certificate is not supported.
That's somehow irritating. There is no reason for that, at least for those who common...
Hello,
My board contains nRF9160 and nRF52840. The nRF52840 is a HCI controller (based on HCI lpuart example). nRF9160 communicates with nRF52840 over UART. I want to perform...
Hi, in our project we use nRF5340 to control some externanal peripherals as flash mem through SPI and also we need BLE comunication.
The case is if whe allow the config...
Hi, I am trying to use the DECT NR+ sample from the 2.7.0 nrfconnect sdk but I can't seem to get the following to work in the prj.conf:
the results of my build give...
Is there a way to convert the firmware for the nRF Connect RSSI viewer to work on the nRF21540DK. I imagine it isn't too difficult, since it is essentially the nrf53840 but...
I have customed a board based on nrf54l15.
Then I built the matter light_buld demo with target 'nrf54l15pdk_nrf54l15_cpuapp' and burned the file "merged.hex" into my custom...
