Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
After getting nrf52 board I've sucessfully recovered it, flashed it with blinky example and I cannot recover it again. I tried doing nrfjprog --recover and nrfjprog --family...
I'm working on a custom board that uses an NRF52840, I've followed the Nordic Developer Academy course related to DFU over uart0 ( Exercise 1 - DFU over UART - Nordic Developer...
Hello everyone,
I have a custom board with a nRF5340 on it that is used as a BLE reader for mobile phones. Now we wanted to do some EMC testing. For this we need to broadcast...
I am developing a board with the nrf5340, and using a PDM microphone for audio input.
I have used the same microphone on the nrf52832 with the nrf PDM driver with success...
Hello Nordic team!
I'm currently trying to get a demo of zephyr's Blink up and running on my Thingy53 device so I have an understanding of how the connections between...
Hello,
I’m working on an nRF5340 project and trying to measure power consumption in low power mode using SDK v2.6.1. I followed the instructions provided on your website...
I am developing a code for Nordic nRF52840 with some sensors:
LIS3DH: accelerometer
BME680: environment
Fujitsu MB85RC1M: FRAM
u-blox ZOE-M8: GNSS
SD Card reader...
Hi Team,
I’m currently evaluating the new custom PCB we designed and need to measure its sleep current consumption.
To do this, I plan to create simple firmware for the...
I was messing around with my nrf52832DK and set it to boot mode now the LED5 is flashing continuously, I've tried uploading JLINK firmware into the boot device folder but...
Hello members,
I have problem and got an error below.
============================================================
c:/ncs/toolchains/cf2149caf2/opt/zephyr-sdk/arm-zephyr...
I am now running Ubuntu 22.04.
The following command fails for me:
sudo docker build -t edge-impulse-nordic .
The error is:
Dockerfile:38 --------------------...
Relates to: Thingy91 nRF9160 SDK v2.6.1 I am having trouble successfully extending the size of the tfm partition. I took a sample static partition file from nrf\boards\arm...
I would like for the high duty cycle direct advertising to restart immediately after the ~1.2s timeout.
[I'm using Zephyr. I'm also really new to programming these devices...
Hello, i´m having some problems with the SIM card on my custom NRF9160 board.
if i try to use the AT%XSIM? command to check for the UUIC state i get the following response...
Hi Nordic Community
I was using the nRF Connect Android App to scan the contents of the advertisements sent by my board.
My device is C7:51:E9:6E:C7:43
My question...
