I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello there. I'm currently looking at the sniffer software
https://www.nordicsemi.com/Products/Development-tools/nRF-Sniffer-for-Bluetooth-LE/Download?lang=en#infotabs ...
Hi,
I'm using nrf52840 and connect to a PC with BLE, using Nordic Uart Service (Rx and Tx characteristics).
When sending messages, I need to know how much data I'm writing...
Morning,
We have a technical question please. As far as we know the NB-IOT services in Germany should use only Band 20 for operation, but we see in our lab tests that some...
Hi
1、The customer wants to set read protection during batch programming，Customers use offline programming during mass production；
2、In addition to using nRFgo Studio to...
Hello.
I know that I can change the interval of the advertize event by changing the advertize interval, but I don't know how to set the interval to be sent to each channel...
Hi, We did design our own board/pcb using the nrf9160, but we have a problem to connect to network/lte. I did some debugging and I found out that when the method lte_lc_init_and_connect...
Can you please tell us what is the power consumption in Idle State with DRX = 1.28s and Sleep State with DRX = 1.28s? And an estimate with eDRX at 5.12 s? We are asking because...
Hello, I am using nRF52832 dev kit. I am trying to get lower current consumption. I used ble_app_blinky example and disabled the NRF_LOG. My settings are below:
Role: Advertising...
Hi, I used my NRF52840-DK for few times but suddenly the jlink connection was not detectable. Before the Jlink failed, the main controller on board did not bring up the board...
Hello,
I Cant upload BLE Code on nRF52832 breakout board from nrf52 Dk using Segger studio. Other codes such as blink are uploaded successfully. But there is problem for...
Hi,
I am trying to use radio notifications (mpsl_radio_notification.h) to call notify with data just before central connects. I do this with no problem with NRF52840.
...
Hi everyone. I just bought the nrf52832 Develop Kit. However, after trying to flash write the sample, my nrf52832 Develop Kit doesn't work and won't flash write the next time...
Hi, I'm using BC805M module which uses nRF52805 SoC.
I have a power ON/OFF button on the PCB. If I press the button (deep sleep mode) during BLE connection, the BLE will...
Hi, I'm using nRF52805.
In my code, I used BLE to transmit I2C and ADC data to the mobile app nRF Connect correctly and continuously.
I tried to use NRF_LOG_INFO() and...
