Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
Hello,
I am developing a BLE peripheral with three services:
Device Information Service
Custom service #1 with two characteristics
Custom service #2 with one characteristcs...
When i enable BLE_DFU_SUPPORT_ENABLED 1 and debug i have problem Mesh error 4 at 0x00000000 (:0). I'm using sdk: 17.0.2, sdk_for_mesh: 5.0.0. Board nRF52840 DK. Thanks you...
Hello!
I am sending MQTT commands over UART from an NRF52840 DK to the NRF9160 DK which has the ibasis sim card inside. I noticed 3 times so far that after 24 hours , 1...
Hi
I could test Bluetooth Mesh Chat sample on nRF52833-DK nodes. I would like to know whether there is any way to send chat message from nRF Mesh app (non-mesh BLE device...
Hello,
I need to send and receive UDP packets using nRF9160DK via NB-IoT network. I'm able to achieve this using Serial LTE modem . However I need to write my own application...
Hello,
In a design we plan to have 2 x SPI, 1 x QSPI and 1 x I2C interface. For the SPI we plan to use one @32MHz and the other @8MHz.
Please confirm there no "instance...
Hi everybody,
we are trying to bring our beacon's consumption as down as possible. We have nRF52832 mounted on our custom PCB with external 32 kHz crystal and DCDC is enabled...
Hi, I am using the Nordic nRF53DK, with the Segger IDE, in the NCS 1.5.0 release.
I'm playing around the Data Length Extension with the Sample of the Central UART...
Hello, My environment is nrf SDK v1.5.1. The board im developing for is the nRF52840DK. I'm trying to do some ECP-Calculations and therefore Ii want to use some function located...
Hello, All
I want to implement OTA using Thread with nRF Connect SDK.
Is there any sample code or reference this can be done with Thread?
Even if there is any experimental...
Hello,
I have a: nRF5340DK connected to Windows10 PC via USB.
I also have these that are working fine in terms of being able to communicate with the nRF5340DK over Bluetooth...
nRF SDK version is 1.5.1
upgrade modem fw to 1.3.0
Is there any way to do software reset on GPS modem? I have ran the gps example and I notice that "printk" sends everything...
I'm using the nRF5340 DK with the HRM example. My phone is HUAWEI mate 10 (Android 10).
I could scan the Zephyr Heartrate Sensor in nRF Connect App and nRF Toolbox App ...
Hi Team,
In continuation with Case ID: 269054, 269278
I am using NCS (as suggested) to avoid high current consumption happening during softdevice initialization.
I set...
