Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
We want to control the BLE Mesh network from the linux. As we understand the only one way to do it now - pyACI https://infocenter.nordicsemi.com/topic/com.nordic.infocenter...
Hi all,
We develop a custom board using MCU nRF52840(Master) and Module nRF9160(Slave).
I confuse to select an available circuit configuration from the reference circuitry...
Myself and others have received this error message
while upgrading nRf Connect for Desktop.
Despite the error message, the installer seems to have completed correctly...
I'm using an NRF52840 custom board along with FreeRTOS and soft-device S140 V6.0.
I want to access the complete 256KB of RAM for verification of RAM using a custom protocol...
Hi I'm considering a design with this precision RTC
I intend to use the 32KHz output on XL1 (and XL2 grounded) as I've seen done here, but the DS3231 datasheet says the...
On both the 51 and the 52, I believe the reset pin is active low, and should otherwise be tied to VDD?
The reason I am asking is that I failed to find this information...
Configuring the GPIO with the following parameters giving me the 3.3 volts on the pin 26.
Is there any way to bring the voltage down to 1.8V through software ?
Hi, I am currently working in Matlab to develop my DSP algorithms and will use the Matlab coder and Embedded coder to convert them to C code. Afterwards I will import the...
Hello,
I am currently trying to build the GPS sample from the latest Code Version. I am using SES on a Windows machine. After starting the build process I have got the...
Hello,
I've been using NRF Connect on Windows for a 3 or 4 months now. During the startup I get a window that reads
Unable to download latest app info: Unable to download...
Hello everyone,
I got a problem with receiving an array data on Android application sent from a custom characteristic.
Below is the code for sending an array data via...
I have been using my 2 nrf52840 DKs now for a while and have been loading and changing the light switch mesh example quite a bit. I have also been using the 840DKs to load...
Hello!
I want the device to immediately stop any data transfer when it receives an external event, stop sending advertising and go to sleep.
How to do it right? After...
Hi Folks,
Can you please let me know if nRF52811 supports XIP (Execution in Place) feature where I can use SPI NOR Flash to the SoC and execute my code directly from Flash...
SDK 15.2
Mesh SDK 3.1.0
Base Example: Enocean_Switch
Im working on creating an LED dimming firmware that uses a long press on the Enocean remote to dim the LED. It works...
