Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
My environment is:
SDK14.1 + SD132 V5.0 + NRF52832
2 sensors(MPU9250 + LPS22HB) 1 battery gas meter (LTC2942) are mounted on TWI ( +1mA)
SPI to spi flash. (+1mA) and...
Hi，
I use SDK is nRF5_SDK_15.0.0_a53641a
【1】In examples proprietary_rf , Here is only the example of pca10040 , So I have to download a lower version of the SDK ?
（...
Hello, I am trying to setup and use the nRF sniffer (ble-sniffer_win_1.0.1) on my NRF51DK (PCA10028) board. I followed the instructions and using nRF studio, I erased all...
Hello!
I'm currently trying to lessen the current consumption of the nrf8001.
I tried to change the connection interval, slave latency, and the timeout using ChangeTimingRequest...
Hi,
I've been using the nRF24l01+ for some time now and am quite satisfied. I'm having a new issue that I'm unable to explain and for which I would greatly appreciate some...
I have filed an issue related to HCI UART sample from zephyr running on nrf52832. I compiled the hci_uart sample successfully, but I am not able to use the UART interface...
Hello, I'm using SDK 15 and softdevice 6.0.
I use the micro as a master and I connected an i2c sensor as slave. I had put external 10 Kohm pull-ups, but I had a low level...
Hello ,
I am using SDK for mesh, I have saved .hex image file in flash.
Is there any example or any suggestion how can I run bootloader which will read data from flash...
HI:
Always error while porting,Error: L6218E: Undefined symbol app_uart_init (referred from main.o).
I added a path, and ENABLE UART_ENABLE 1 in sdk_cofig.h
Compile...
I have set up the gcc toolchain on Mac OSX to compile my BLE nRF51822 code and I tried to flash the code. Here are the 3 scenarios that I have tried (JlinkExe on Mac)
Case...
Hi,
I am not sure if this is the right place to open up a thread about a zephyr HCI firmware issue. Since Nordic also contributes to zephyr I'm putting up this question...
Dear All,
We have designed our custom board based on nRF52810 chipset. wehave not used 32.768khz oscilator. it seems in code default configauration is with crystal. so please...
Hi All:
When I simulated PWM by GPIO, the output current noise was shown like the picture below (red circle area):
Cause it will lead to a loading issue in the backend...
I want to implement a long write. The environment in use is below. · SDK15 · Nrf 52 · Nrf 52832_xxaa · S132_nrf52_6.0.0_softdevice.hex
My start is "nRF5_SDK_15.0.0_a53641a...
