Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello,
I am working on nRF52840 custom board, in that, I was facing issues with sd_softdevice_enable().
When I call the sd_softdevice_enable() it's stuck. Not return from...
Im using SPI interface to read data from https://docs.rs-online.com/7d34/0900766b81327f26.pdf using the D2 opcode.
The opcode starts reading the page from the flash (528...
Hi,
we are not able to see any output in NRF connect APP in FFBM mode with DTM Firmware,
However , on flashing complete firmware, we are able to turn on Beeper in FFBM...
Hello Nordic support,
I have a Zigbee coordinator application which has declared the time cluster as a server. I have a zigbee end device which has a time cluster as a client...
Hello I'm using nRF53 DK on zephyr v1.6.1. I'm now testing the power-saving mode. I tested the system-off example "v1.6.1/zephyr/samples/boards/nrf/system_off" and it works...
Hi,
I am using nrf52810 chip. we are trying multilink with central(1 central and two peripherals connected at a time),one central and one peripheral is fine, but we are...
Works on Huawei P20 Lite (Android v9), Samsung J3 (Android v7.1.1), all IOS phones. Doesn't work on Samsung A50.
Samsung A50 does see the devkit when using the same firmware...
OK, full disclosure - I'm pretty new to the whole nRF Connect/Nordic Semi environment, having had to jump across here after all the issues with silicon availability meant...
I would like to configure GPIOs as compatible = "nordic,nrf-gpio"; in devicetree file.
I did check this topic, but I think that this kind of configuration defeats the whole...
Hi, I'm working on a FreeRTOS (I just start to use it, so I'm a beginner) project in wish we want to use an external 32 MHz crystal. The program has a task that should be...
I want to implement CENTRAL using nRF52810. To implement the central, the softdevice must be s132 but I am not familiar with the softdevice concept. Until now, the softdevice...
Hello,
I closed below case by mistake.
nRF9160 receives garbage data on UART sometimes - Nordic Q&A - Nordic DevZone - Nordic DevZone (nordicsemi.com)
As per your...
The Thingy:52 application uses LIS2DH in low power standby mode and the MPU-9250 for advanced motion tracking.
Why machine_learning firmware used LIS2DH sensor instead of...
Hello developers,
I am using nRF52840 feather from adafruit as a ble central board.
FIrst of all, I tried to filter just only for my beacons with UUID. I saw a ble central...
