Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
I have followed https://devzone.nordicsemi.com/nordic/short-range-guides/b/bluetooth-low-energy/posts/ble-advertising-a-beginners-tutorial
i WANT TO ADVERTISE the battery...
Hi,
Segger SystemView 3.30 (downloaded from https://www.segger.com/downloads/systemview/ ) does not work with NCS 1.5.1. Upstream Zephyr has updated https://github.com/zephyrproject...
Hi Nordic,
I just had Thingy:91 few days ago. I ran this KIT with thingy91_nbiot_2021-03-04_8e8c6089.hex and asset_tracker example in ncs/nrf/applications . I found that...
I would like to send and receive data to/from nrf52832 pins over BLE using android phone. I would like to capture and display output of Force Sensing resistor and control...
To the kind attention of Nordic support team,
We have got an nRF52833 gzll host that has to interact with multiple gzll devices. We empirically saw that (in our case and...
Hello
I'm using the CLI example as ZC and a custom endnode based on the freeRTOS multisensor example (from nRF5 SDK for Thread and Zigbee v4.1.0). Im trying to send a counter...
Hi, I have a problem with setting up SHELL over RTT. I have managed to get some logs from the device. Prompt `rtt:~$ ` is also shown. but whenever I try to send something...
Hi,
we just uploaded MFW 1.3.0 to our nRF9160 DKs that had engineering revision of nRF9160. They seem to be now bricked and it is not possible to downgrade to MFW 1.2 via...
My task is to create a webserver on the nRF9160DK. For this i'm using the civetweb module provided by zephyr and the ethernet-shield from PHYTEC. I got an issue i want to...
Hi everybody,
I have developed a BLE sensor based on nRF52840 (S140 6.1.1 and SDK 15.3.0) that is normally performing connectable scannable undirected advertising. Since...
Hello,
I need to use the ADC with 600mV internal voltage, ADC Gain stage = 1.
The input signal on VINP vary from 750mV to 1750mV, and input signal on VINN is fixed at...
Dear friends,
I followed the tutorial( Using serial interface for provisioning and configuration ) control a mesh node.
a) The PyACI as a host via uart connet to 52840...
Hi, teams.
I checked the operation of nrf mesh network. (mesh sensor example, and light switch example)
It works well. Thank you!
By the way, I have a question....
Hi everyone,
I am having a problem with dfu example. I would like to test my board with the buttonless dfu image, namely
sd_s132_bootloader_buttonless_with_setting_page_dfu_secure_ble_debug_without_bonds...
Hi,
I saw a similar post ( Case ID: 249969 ) and this just happen to me.
I have not used my nRF52840 DK for a few weeks. It has been in its original plastic bag the whole...
