Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi, I want to add PPP protocol to the Zephyr mqtt_azure example. I am using an nRF52840-DK with a Quectel BG-96 Modem. The generic Zephyr gsm_modem example using PPP is working...
Hi, I am using nrf52840 with S140 Soft device and SDK for Thread v4.1. In our test setup we got around 50 FTD devices in the same network. In some time interval we need to...
We are trying to connect the nrf9160 to a spi flash device. we have a custom board with the following pins connected:
sck: 27
mosi: 28
miso: 30
cs: 29
wp: 31
reset...
I would like to use the CC310's SRP accelerator with an application that uses S140. The uC in question is nRF52840.
I have added this code to the ble_app_blinky example...
Hi,
As per nRF52840 datasheet, the accuracy of internal temperature sensor is ±5°C. We want our device to be operational between 5 °C to 40 °C.
When we tested this extreme...
Hi,
I want to use the Zephyr network stack with its libraries on the nRF9160.
I tried to use the Zephyr tcp functions with the Zephyr network shell commands (eg. shell...
Hi Everyone,
We are using nRF52840 IC for our products which has 1 MB of flash.
Thread Secure DFU Example provided with Nordic SDK supports Dual Bank DFU. This limits...
Hi Team,
We are using the nRF52840 for our development purpose. For sake Cyber security purpose we need to disable the Jtag debug port.
For this we have used the below...
Hi Team,
We have seen 10 instances in past 2 months where customer mobile phones failed to discover BLE device. This has happened 8 times with Moto G7 power (Android) and...
We have a module based on the nRF52840, today we loaded the pre-compiled hex file for the BLE DTM code to 2 nRF52840-based modules and noticed when using the nRF connect DTM...
Hi !
I want to whiten the BLE Advertising data(channel 37,38,39), but I don't know how to do it.
I tried many things, but nothing worked.I'm on 52832 platform Flash_S132_NRF52_7...
Hello,
I have got three nRF52840 Dongles to test Bluetooth mesh. I have been going through the devzone queries and found that many people have previously asked about SDK...
Hello,
I am using the nRF52832 with the s132 SoftDevice. I've been trying to interface the VL53L0X sensor to get ToF readings. I'm using the code of this driver . When calling...
Greetings!
I am using NCS 1.4.99. I have spent some time debugging my I2c application on NRF5340 and I came to the realisation that I was not able to control any pin that...
