Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
I am using S130, SDK13 and NRF52832 both on my central and peripheral - custom boards.
I am trying to avoid service discovery on my peripheral.
I have set the service_changed...
Hi, Does anyone know how to modify the asset tracker so that rather than point to the AWS URL it points to a fixed IP address?
Also is the port number fixed?
Hello,
I am playing around with the Blinky example on my custom board, where I have one button and two leds. Everything works fine and I can control the LED2 and detect...
I have a question about PeerManager.
SDK: 15.3.0 example: ble_app_multirole_lesc (I changed the source from the sample) using device: EYSHJNZWZ (nRF52832)
When connecting...
Hi,
When I test nRF MESH application on android phone with other mesh device, after discover services, it always use proxy data in to write data to device for provisioning...
Hello there,
We are planning to use MQTT and nRF5 boards in the project. We've successfully tested out MQTT examples provided in the SDK using BLE router on Raspberry Pi...
Hi,
We are trying to establish communication between ESP8266 and NRF52832 over uart using Baudrate 115200, We are also controlling the ESP8266 boot and power through GPIO...
Folks,
I have read through a lot of threads on here trying to solve this and believe I have tried everything to no avail.
I am finding that I cannot get the nrf52832 to...
Is it possible on the central device to create secure and unprotected connections simultaneously with different peripheral devices? How should the peer manager be configured...
Hi,
I'm writing an application to communicat on BLE with an IoT device.
I connect well, and can write on characteristic but normally I should receive notification after...
infocenter.nordicsemi.com/index.jsp
<info> app: peripheral init ok <error> nrf_sdh_ble: sd_ble_cfg_set() returned NRF_ERROR_INVALID_STATE when attempting to set BLE_CONN_CFG_GAP...
Hi,
I was wondering if there is some kind of SIP client example code available (or in progress) for the nRF9160? For a new project, we are investigating to use the nRF9160...
I'm currently working with nrf52832 implementing bluetooth and spi functionalities. The bluetooth connection to PC is working fine, it connects and after that starts transfering...
Hi,
It seems I am unable to open the asset tracker application in SES. I get the following CMake error:
I've followed the nRF Connect SDK getting started app, and all...
I have a BLE device acting as a central and a peripheral, relaying information between that peripheral and a custom iOS app. As a central, it reads (not notifications) the...
