Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
In the course of investigating higher than expected current consumption, I've been looking at nRF52832 errata, and one that I'm concerned about is #78, use of Timer STOP task...
Hello,
I have been trying to merge the pwm_library (or gpiote) with ble_uarte examples to have controle on the pwm signal through UART events
I think i merged correctly...
Hi everyone.
I'm trying to transfer new firmware over UART for just only one node in mesh network.
My node will connect to other wireless MCU(ESP32, ESP8266....) over...
I'm using FreeRTOS and trying to get push button events to fire. The events would fire if I held the button down long enough. I found out that the problem was that "FREERTOS...
Hi
I have a custom board implementation that operates as follows:
Monitoring an input pin waiting for low high transition, BLE advertising of device.
When input event...
I'm having trouble having multiple characteristics for my custom service. My main.c looks like this:
Even though I have 2 characteristics added here, I can see just the...
Hi,
I had a few nrf51822s lying around and as I find the chip and the SDK quite convenient to use, I thought about using them in a small MCU project which does not need...
Above you can see the original and commented out modified code for the given example. The modification causes crush to
NRF_BREAKPOINT_COND; // On assert, the system can...
Hi,
I was looking at the Thingy-52-to-nrf52xx demo. I want to capture raw motion data no a DK and save it for further processing. Are there any options (I guess one is nRF91...
hi
i read in earlier questions on the devzone that nordic offers to review the schematic and layout as well as perform tuning free of charge to their customer. Is that still...
Hello every!
I am testing FATFS example with nrf5284 PDK .
CLK - P1.15
MISO - P1.14
MOSI - P1.13
CS - P1.12
My micro sd card module work correctly with STM32 MCU. I...
Hi all,
I am Using SDK15, chipset is nrf52810 , In ble_app_uart application i have added the BLE_NUS_C and TWI application code , before this i have added only TWI to ble_app_uart...
This blog describes how to set up SES (Segger Embedded Studio) for use with nRF SDK:
https://devzone.nordicsemi.com/b/blog/posts/segger-embedded-studio-a-cross-platform...
i'm using DFU for my project, it worked fine until devices has been bonded , DFU cannot work again. i checked and find out that after running interrutps_disable() , the devices...
