Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
We originally saw (and reported) this problem with nRF5 SDK 4.1.0. We switched to nRF Connect SDK 1.6.0 which did not exhibit this problem. Now we just tested with nRF Connect...
Hi, I'm trying to found a way to flash production config for a project based on zigbee NCS example with OTA. Is nrfutil still a valuable tool for creating a production config...
Hi.
I'm trying to emulate my project, which is intended to run in either nRF9160 or nRF5340 boards (both using Arm Cortex-M33 processor), using QEMU, but as far as I know...
Hello,
I am using nRF52840 microcontroller to communicate with an external integrated circuit, through I2C peripheral . The project is using the latest Nordic SDK: more...
Hello,
I am running 1\nRF5_SDK_17.1.0_ddde560\examples\dfu\secure_bootloader\pca10040_s132_ble\ses example of SDK 17.1.0. Now, I want to update the firmware when it is pressed...
Dear Ladies and Gentlemen,
I read for detecting angle of arrival the following page:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth...
Hi,
I want to develop simple app that receives data via BLE and send it through UART so I could gather them to file or draw a real-time chart in SerialPlot.
As far as...
Running the secure DFU example in SDK 17.1.0 results in hardfault in IAR EWARM 9.10.2. The board used is PCA10040.
Using EWARM 8.50.4 seems to work without problems.
Steps...
I have a number of custom projects and boards that were created using SES.
How do I get nRF Connect to see my projects and boars. I have a separate directly structure where...
if i am controlling two spi devices with one instance, can I just define a new SS in the same SPIconfiguration or do i have to close the connection and select a new one? ...
As soon as I plug in my nRF52840, the whole board gets extremely hot. When I try to upload a program, the error message "No J-link device connected" pops up.
With another...
Hi!
I use XMONITOR to get the current cellid but it seems strange.
%XMONITOR: 5,"","","24008","2725",7,20,"01ADF70B",215,6400,50,35,"","11100000","11100000","01001001...
I'm working on nRF9160-dk.
I built a sample application "serial lte modem" in NCS 1.6.1.
i can use AT command on the UART0, but i find the printk in source code is not...
I have successfully compiled my project using `west build` and now I am trying to load it onto my nrf5340 board I recently purchased. Here's what I'm doing:
- From the same...
