Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
I want to measure the duration of a single pulse using GPIOTE , PPI and a Timer with a NRF52840.
My initial idea was to have two capture tasks for the GPIO events...
Hi There,
I try to develop an application in intermittent conditions, it will off work frequently as for lacking the energy.
I try to resume the application from the last...
Essentially the title. Given that I have a BLE device which I have configured to have Legacy DFU services, and also customized the DFU service's UUID, how would I go about...
Hi,
I have nrf9160-DK and I am using NCS v1.6.1. I am trying to run HR Peripheral sample application on the nRF9160DK board.
I have flashed nrf52840 with hci_lpuart sample...
I am trying to using nRF52833 and nRF52840 as a BLE central to connect customer's BLE peripheral.
The attached screenshot is the service discovered by nRF connect Android...
Hello,
I am developing an application based on the BLE examples from the nrf5 sdk using he Segger Embedded Studio.
I am porting a library for a peripheral component and...
https://devzone.nordicsemi.com/f/nordic-q-a/80125/want-to-achieve-1-2-mbps-through-ble
Issue is in this link is not properly addressed . I want to work on BLE with good...
How much i can apply maximum and minimum voltage at Analog pin of nRF52832 controller IC? And Please also guide me is there any mention in the nRF52832 Datasheet.
Hi all,
I am using SDK = 15, softdevice = v6, chipset:nrf52810
I have used ble_app_uart and SAADC example code for one of my application, its working fine, and next i...
Hello,
I'm using nRF v1.5.1 SDK.
If I have my RX buffer to be of size say 6, and I transmit 7 bytes then my code will detect a full RX Buffer and go to the endrx_isr...
Hello,
Looking at the errata entry [78] TIMER: High current consumption when using timer STOP task only , I see that it recommended to use TASKS_SHUTDOWN instead of TASKS_STOP...
Hi everyone,
what are the tolerances of the internal reference voltage of the ADC (0.6V) at room temperature? I know the tolerances are included in the gain error and are...
Hello,
I'm following this documentation Doc to include Fota upgrade on peripheral LBS sample but I have the following problems:
1) all file .bin like ( app_update.bin...
I'm using dongle nRF52840 to sniff packets between earphone & iPhone.
I am facing the same problem: " Encrypted packet decrypted incorrectly (bad MIC)"
just after LL_ENC_REQ...
HI,
I'm developing it using NRF52832.
I'm updating the remaining battery capacity using saadc. However, the battery value is not stable because the value obtained from...
