My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
I am facing an issue in writing data to a register of my bmp388 sensor using I2C.
If I fill my transmit buffer of 2 bytes in following way , tx_buf[] = {register_address...
hi support team,
i was testing this this example " http://developer.nordicsemi.com/nRF_Connect_SDK/doc/1.4.0/nrf/samples/nrf5340/netboot/README.html#nc-bootloader "
i...
Hello all,
We are trying to implement coexistence between BLE and Bluetooth mesh.
After following the Nordic coexistence tutorials, our program builds fine using both...
I have worked with the nRF51822 and the nRF51 DK and used the pc-ble-driver on the nRF52840 dongle. Now all I am interested in the BTLE development, not mesh. I found out...
Hi
I did some experiments with the GATT capabilities of the S140 7.2.0 softdevice. An experiment that I did showed a behavior that is not as I would expect it.
Steps to...
hi professor,
I use the zephyr spi driver to control spi nand flash.I want to send two bytes and read 3 bytes. But between write and read time sequence there are 10us delay...
I'm testing nRF Mesh on nRF52840 chip, I used P1.10 for LNA pin and P1.13 for PA pin, I tried to config but it not worked. how to fix it?
static mesh_pa_lna_gpiote_params_t...
Dear support team
Please note my sample application code attached, and the trace of the I2C transmission
I am facing the issue that the twi driver does not write more...
Now I am using nRF52840 I want to get data from a sensor via SPI. I configured the SPI pins like this P0.11 -> SPI_CS P0.12 -> SPI_MOSI
Actually, I couldn't get any data...
Hi Nordic-Support,
I am trying to figure out how the boards in ncs/nrf (e.g. thingy91_nrf9160) are made available for applications. I cannot see how they are added to the...
Hello,
I would like to take a photo and send it via Zigbee to another on nRF52840. Just a single image that is around 600x480 sizes. What interfaces can I use for that purpose...
hi,
i am including spi in ble_uart program .i am getting error "'NRF_DRV_SPI_INSTANCE_0' undeclared here (not in a function); did you mean 'NRF_DRV_SPI_INSTANCE_'?".
