Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello fellow Nordic-ians,
I am developing a custom firmware for Nordic Thingy 52. I am using the Segger Embedded Studio as my IDE and J-link Edu Mini as the programmer ...
Hi,
I have found zboss 1.0 opensource.
Surveying the source, i have noticed that variable "g_zb" (nicknamed by ZG) give system informations.
I can find zed address(16bit...
Hi,
Here is my setup, NRF52832 PCA10040 s132, sdk 13.0.0.
I work on Windows 10 with a server (The aim is to do it from a Raspberry later) which one is connected to my...
Hi,
I'm developing a simple sensor application using s132 on NRF52832_XXAA. The application works fine, except that I have problems disabling the saadc module after conversion...
Hi, How can I configure so that I can transmit real GPS data of the device and watch it from nrfcloud? I think I need to change something in config files? Simulated GPS data...
Hello,
in the ble_advertising_start() function of SDK15 I noticed, that the check for the secondary_phy is the same as for the primary_phy.
I assume this is a copy paste...
Hi.
I am trying to choose the crystal and external capacitor for nRF51822-QFAA-LDO. I found the crystal with load capacitance 10pF. As mentioned in reference paper,
...
Hello. I am having problems when I connect one of my PCA10056 boards (nRF52840-DK) to my Windows machine and run nRF Connect v3.0, Bluetooth LE app v2.3.0. When I select the...
Dear Friend,
Using this tutorial I imported a Blank Blinky Kiel Project of SDK 12.30.
I am using a custom board with nrf51822, I imported the PCA100028 version.
...
Hi,
i am working on power management for nrf52832. i used icm20948 for gyro and accelerometer. my battery capacity is less. so when my mcu is going to sleep but gyro and...
Hi,
What is recommended to do for update SEGGER Embedded Studio for ARM 4.12 to newer version?
Is there any update tab from SEGGER or I need to download and install from...
Hi all! We have to work with PPK and nRF52 DK. For a measurement was used Power Profiler application from nRF Connect tool.
Is it possible to do the measurement in interactive...
The Interface MCU Firmware link provided on the nRF52840-DK page is the same as the firmware for the nRF52-DK. Unfortunately, these boards use different nRF MCUs. Loading...
I'm using Windows 10 latest updates installed.
I can successfully build v0.4.0 but none of the other releases of lte_ble_gateway
The common error is as below, any help...
Hello,
In our project there is a problem that we encountered is happening when the Nordic BLE mesh advertising and connectable advertising for GATT connections are enabled...
