Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I have the following Device Tree in my application:
I get the error -134 during the application startup. Debugging the application shows that the error happens...
Hi, I'm developing ble applications.
But there are problems on calling Ble APIs.
If I call the functions that conatins bt_le_adv_start() in main loop(Maybe main thread...
Hi,
I have a BLE interface with services and characteristics and I want to have different level accesses for my characteristics with for example two levels:
level user...
Hi,
Setup:
nRF NCS 1.9.x and nRF NCS 2.5.0
nRF5340 and nRF52840 both with an external crystal attached to HF clock input.
Problem:
Inaccuracy in timing of UART at...
This is sort of a hardware question, involving the RADIO peripheral in the nrf52(840) line. The question is simple. Is there any limitation on when you can change the TXPOWER...
I have a driver for a Piezo buzzer running on bare metal that I would like to port to the nRF connect SDK. The existing PWM-based driver in Zephyr does not fulfill my requirements...
Dear Nordic Team,
I want to connect my nRF9160DK board to my nRF7002DK board and get a wi-fi location. I've followed samples/cellular/nrf_cloud_multi_service as sample...
I have a question about Serial Modem firmware and the AT#XCMUX and AT#XPPP functions.
Are these commands available in the Serial Modem example in the Quick Start?
If I...
Hello,
I've been working with nRF9160 for a while now and wanted to let you know, I love this little piece of hardware. The possibilities, the small form factor, the power...
Hello~
I am developing nrf52840 with zephyr ncs tool chain v2.7.0 and SDK v2.6.1.
Our hadware is very simple, just a power IC, a nrf52840 and a G-sensor.
Our pre-production...
We have used zigbee sample for coordinator we did many changes in that like subscribing and sending values in UART when any new device gets added.
but noticed ZB_ZDO_SIGNAL_DEVICE_ANNCE...
Is there any plan to support Bluetooth Channel Sounding in Zephyr OS apart from nrfConnect SDK? If so, when can we expect a pre-release version to be available?
I am using a nrf52833 with NCS and was wondering if there are events I can subscribe to (or polling if events don't exist) that will notify me when USB power is connected...
Hello,
after some trial and error, I managed to use the "Bluetooth: Direct Test Mode" example with NCS 2.7.0 (Sysbuild) and USB.
Now I'm questioning myself how to correctly...
