Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I need to install a BTLE application on an nRF52840 dongle that is enclosed in a case and therefore I do not have access to the reset button.
I have looked at some of the...
Hi, I'm using nRF52805.
My BLE code could connect & communicate data perfectly for the first time. After the disconnection, I can still see the signal. However, when I try...
Hello, new-to-this platform dev here!
I am implementing BLE bonding on my nRF52840 DK, which uses the S140 Softdevice. The DK is a peripheral and I'm using version 17.1...
Hi,
I need some help to choose an RF module for a new project.
I need:
* To connect to nRF24L with custom radio communications
* to connect to legacy standard bluetooth...
I use the nRF5_SDK_15.2.0_9412b96 , the sample is use a QSPI FLASH(MX25R64), and we want to change this QSPI FLASH. we will use GD25Q64E, which code should be modify?
I have developed a project with 9160, which requires real-time display of NB network signal on the screen. In order to save power consumption, I have set the Mode to PSM Mode...
Hello,
For us our IO rail is 1.8V. In this case do you see a big difference in power consumption whether REG1 is in LDO mode or DCDC mode? From 1.8V to 1.3V if in LDO mode...
Hi.
I use latest version of sdk and mesh. I run co-exist example as client and server in switch-light example as server. in client side i have add group address as you have...
Hello:
I had the Thingy91 (nrf9160) configured and working, but after a while, I tried to test it again, and I started seeing these errors:
- When using the LTE Link Monitor...
Hello,
I am working with DFU in the nRF Connect App and its working fine. Now I want to switch to the Android-DFU-Library and I always get "DFU CHARACTERISTICS NOT FOUND...
Hello,
I am currently using mqttsn publisher exams with keep allive time of 30 seconds, so according to MQTT standard if period of inactivity will be 45 second and the client...
Hello,
I would like to sign a firmware image with a custom private key. This is intended for OTA firmware update. The key type is ecdsa-p256 and the file containing the...
Hi，
sdk：ncs v1.6.1
board:9160dk_nrf9160
I use RTT to output log data, but I found that it can only output about 1k characters each time. Where can I modify it?
this...
Hi Team,
These are the SDA and SCL lines of nRF52832 connected to a sensor. the clock frequency defined in the code is 400 KHz, but its coming as 200 KHz on oscilloscope...
Hello, I have designed a custom hardware using nRF52833. I tried to program the nRF52833 using nRF52832DK, I am having following connections- nRF DK nRF custom board VTG-VDD...
