Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I am unable to locate the list of error codes , in my code I get "sd_ble_gap_scan_start returned 0x10" as I use sd_ble_gap_scan_start() function with input parameters...
Hello,
I am trying to program and use the AWS IoT example to send data to the amazon webserver. I worked through this post ( https://devzone.nordicsemi.com/nordic/cellular...
Hi,
I am designing a module based on the nRF52805 and wonder if there are also GPIOs that should not drive high frquency, like stated here for the nRF52832:
https://infocenter...
Hello,
Is the MBEDTLS_USE_PSA_CRYPTO functionality supported in nRF SDK 1.6.0 (nRF9160)? Setting this value in Kconfig doesn't seem to propagate to nrf-config.h.
If I...
Hello,
I want to transmit data gain from an i2C sensor from one nRF52832 to another via BLE.
I have successfully configured i2C and now I can store those values to Variables...
Is it possible to get the PPK2 to return the voltage VDUT+ (VDUT_SENSE) instead of the current when taking a measurement?
if so what is the command?
Thanks,
Mar...
Hello all,
There is a strange case where a custom board with nRF52840 is able to connect to JLinkExe on a Linux machine with the JLink debugger present in nRF52840 DK but...
Protocal :ESB
Devices : 1:central(PTX) 2:peripheral(PRX)
Description:
1、Central transmits data to Peripheral,and then Central receives respond data from Peripheral ...
Hello,
myself and my team are evaluating the use of Nordic Connect SDK offering on nRF52840-based board.
From what I understood, aside from the open source and common...
I have an OTA issue with Galaxy Note 10.
During OTA, phone transmit an odd packet, abnormal offset and some overlapping data.
in debugging, i got to see the abnormal...
Hi,
For our application we need time and date updates from a mobile phone. Bluetooth has a standard Current Time Service for this. However I can't find this service in the...
I use two nrf5340dks to run the routines in NCS \ v1.5.0 \ NRF \ samples \ ESB; The distance between the two nrf5340dks is only 10cm. When the transmission interval is set...
Hi, I'm programming both Central and Peripheral.
[Picture 1] is what I want to implement.
[Picture 1]
Central connect multiple peripherals which is the same functionality...
Hi,
This problem was found accidentally when trying to solve a different problem here: devzone.nordicsemi.com/.../nrf52833-peripheral_uart-zephyr-example-only-works-with...
