Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello,
My board is connected to Gyro, Magneto sensor.
And board is sleep and wake-up by GPIO.
It usually works well. But time to time after wake-up from sleep mode...
Good Morning!
I try to update the modem firmware of a nRF9160 chip.
When I connect it with the nRF Connect v3.6.1 - Programmer (v1.4.10) and try to update the modem with...
Hi all
For the nRF52832, the total maximum sink and source current is recommended to be 15mA in this devzone entry .
Unfortunately, it seems like there is still no value...
I want to add an external button that mimics the properties of the buttons in the nRF52 DK. I read that the switches are all active low, so I assume that this means they are...
Hi,
in peer_manager.h and id_manager.h the docs say a function can return
BLE_GAP_ERROR_WHITELIST_IN_USE
But the error code is called
BLE_ERROR_GAP_WHITELIST_IN_USE...
Hello,
I have an nRF52840 on a custom board. The nRF52840 has been pre-flashed with the Adafruit UF2 bootloader for early development exploration. As the project moves forward...
Using SDK15.3 and S140
following from my previous support request regarding TWI sleep current, I got the newer AIS2DW12 accelerometer and I have successfully connected...
Hello everyone!
I want to develop and app the sends some sensors data over BLE.
I am trying the peripheral_uart sample of the NRF Connect SDK but it seems that I cant...
Hi, there:
based on \\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132, I need add justworks BLE secure connection.
Do you have any document...
Hello, I want to use Multiple Connection (Multiperipheral sample) to connect with multiple IOS phones at the same time to implement UART. Currently, up to 9 units are set...
I am trying to advertise the shotend name of the device no the complete local name, so code looks like follow
After scanning I can still find the name in the advertisement...
Hello, we are using nordic SDK 16.0 and mesh SDK 4.2.0.
In our project, sometimes at the start of the program, we are running into line 280 of mesh_config.c, a debug assert...
Hi, I am using nRF Connect SDK 1.5.1 with the nRF9160 Modem Firmware 1.3.0
I have implemented an application on the thingy91 with the gps driver (continuous mode) and the...
Hi,
I want to build a mesh network which includes least 12 server node an 1 client node.
I used light_switch example to send 12 byte message packets to client node from...
Hello, in my project i simultaneously use MPR121 touch sensor controller and GPS module connected to UART0 of nRF52840 (custom board). To handle touch events, i use MPR121...
