We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
in my application i am using the hrs application and added dfu and uart service to it.
Q1)how dfu service works?
For my board i removed the total flash so steps i have...
Hi i'm going to do a school project with bluetooth mesh network so i was wondering if bluetooth 5 supports it and what are the benefits of using bluetooth 5 over bluetooth...
Hello All,
Can i use nRF52810 SOC for mesh networking. is there any space constraints?..
if we can use can we control all the nodes via smartphone .
please provide...
I am using nrf52832 peripheral and ble central with some android application .if an app opens it we get ble disconnect event and if we kill the app ble_disconect will come...
nRF52840 OPS 0.5.1 lists the following highlighted sensitivity spec:
The Bluetooth core spec defines sensitivity for this payload length as a BER of 0.017%, not 0.01...
Hi
We are trying a Nrf51-Dongle in a school prosject here in Norway We need to use one of the GPIO pins on the Nrf51-dongle as input When this input is 1 , we want the dongle...
Hi ,I am using nrf52 DK with mpu9255.I am using source code given here here .of this link,I have taken 'nrf5-ble-data-ready-interrupts' example .code builts fine in keil v5...
Using nrf51422 in KEIL. I am verrrryyyy new to this type of programming. I have been looking at multiple examples within the nortic github to find how to input analog reading...
I started Heart Rate Monitor app "ble_app_hrs_pca10040_s132" on nRF52 evaluation kit (nRF52832). Everything work well when I connect with nRF evaluation kit from Android devices...
Hi!
I just got my PCB with a Telit BlueMod+S42 Module on it (nRF52832).
I' using the LESC feature and ist works properly on the PCA1004 and on the Telit DevKit (same Module...
Hello,
I'm working on a bootloader based on the example of SDK13.1. I want to add two more characteristics to the DFU service, but after I add them, the nRF Connect app...
When I use sdk14.2 nRF52810 ble_nus_string_send to send data to a mobile phone android, the first connection is no problem, but disconnected again after connecting problems...
Dear friends,
If i set the conection interval=100ms and the slave latency=1, the slave will wake up every 200ms. If the slave has data to send, it will still wake up every...
I haven't been able to find a drawing file for the nRF51 Development Kit. Is there one out there?
Ideally, I'd like to get the drawing and a *.STP file for SolidWorks.
