Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
My goal is to control a RC toy drone (4-ch 2.4GHz) from a PC. I've seen some hacks (for example dzlsevilgeniuslair.blogspot.com.br/.../more-toy-quadcopter-hacking.html) using...
Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
I'm trying to implement a PRE_KERNEL1 timer (with top priority 0 ) to toggle an LED.
I’m able to control the LED using registers, and now I want to add a timer layer...
I want to send a custom message using a custom Property ID in Mesh Sensor observer example. How do I add a custom Property ID? Currently, I am using #define CUSTOM_ID 0x1234...
I am debugging an application on a nRF5340 DK using nRF Connect SDK from VS Code. (Toolchain/nRF Connect SDK v2.9.0), everything up-to-date.
The build is "optimized for...
nRF52840, nRFSDK 17.0.2, SoftDevice S140 v7.2.0
Hello! We're turning on SoftDevice and using the PA/LNA pin control to drive our FEM. Then, we disable SoftDevice and issue...
Hi,
I found a bug in the init part of the LIS2DU12 driver. The driver tries to reboot the LIS2DU12 sensor using the SW_RESET bit in CTRL1 register even if it is not in...
Hi,
I'm trying to synchronize a process using an nRF52833 dev kit using a Zephyr event.
The code looks like this:
The first routine sends an event and the second captures...
I am working on an nRF52-based device using nRF Connect SDK (NCS) version 2.7.0. The device is configured to enter deep sleep every 60 seconds and wake up via a GPIO interrupt...
Hi,
I'm using the nRF Cloud multi-service application on my Thingy:91X.
I am using the Serial Terminal to see what networks are available, but when I go to attach manually...
Hello,
I've been working on a project using nRF52832 + NCS 2.1.1 including BLE and some sensors : MAX86150, MAX30205, MP34DT05, LIS3DH
I'm sending data of these sensors...
Hello! What are the steps I need to take to switch from BLE protocol to lets say the Gazelle protocol? Is it as simple as disabling the Softdevice? If such a function exists...
We are finishing up development of our product and looking into creating our Bluetooth listing. We are using the NRF52840 SoC (Fanstel BT840F model) with softdevice and NRF...
Hi,
I am working on an application using the nRF52840 with the Quectel BG96 modem. I can successfully communicate with an insecure MQTT broker using the BG96 modem. Now...
Hi!
I'm making a new board using nrf54l15 and I found the following issue:
/* * PWM signal can be exposed on GPIO pin only within same domain. * There is only one domain...
We have a custom board with the NRF52840 running NCS v2.8.0.
We have a problem where our device will crash/lockup. From our testing so far, it seems to be related to Bluetooth...
I have a project for the NRF5340 with SDK 2.6.1. I test the code with twister using Unity and CMock. That works great. But now I have to adapt the unity_cfg.yaml (which is...
