Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hello everyone,
I am trying to execute Nordic Bluetooth ESL tutorial with PAwR. Here, I am able to change the images and handling the state of an LED connected at the Tag...
Hi,
We are encountering an issue where the existing firmware does not run on the chip when powered by a coin cell, even though a 3.3V power supply is available from the...
When I compiled and flashed the Nordic Distance Toolbox example onto two nrf5430dk boards without changing any options, the following message appeared on one of the UART ports...
Hi,
I have the following scenario:
nrf5340
SDK 2.1.1
HFCLK: 32Mhz crystal
LFCLK: square wave of 32768 Hz from an external RTC, range [0 - 1.8] Volts
square wave...
Hi, I am using a custom nrf52832 device. In that device , button is connected with reset pin P0.21. due to reset functionality I am not able get interrupt from button.
how...
Hi,
I am using nrf52840 to develop a product. I use NCS sdk v2.5.0.
I developed a project based on the [Bluetooth: Central HIDS] example in the NCS SDK. This example enables...
Hi,
i am using SDK 2.1.1 with nrf5340.
I would like to add the linker option --wrap.
What are the possibilities to add this option in Visual Studio Code ?
Could it...
Hi,
I am using nrf connect SDK 2.9.0 with nrf52840DK and MCUboot with own RSA .pem file (from older versions, so no ECDSA possible). How can I increase verbosity when building...
Hello,
My BLE peripheral code works fine with Android devices, but it is failing with iOS devices. I am encountering an error message: "Ignoring data for unknown channel...
I'm working through the tutorial here. https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-4-serial-communication-uart/topic/uart-driver/#uart_config...
I'm working with nRF52840, my function will read wav file from SD card and play it using Zephyr I2S driver. My source code about playing sound in below.
The strange is the...
Hi,
For a meter application with battery, I want MCU is sleeping but comparator still working to count a pulse input (freq <100khz)
Can Nordic IC can support this idea...
Good day. I'm working on a custom board that uses nRF5340 as the main MCU with a WIFI module, nRF7002. The nRF5340 and nRF7002 are wired based on the nRF7002DK. When I uploaded...
My project as above.
I'm developing my code in nrf52832,with nrf SDK v17.0.0.
I try to add some customized params by FDS so that I can get them after the next run.
The...
Hello,
I am having trouble reading an interrupt on an nRF5340. This is on a custom board using the ISP2053 SIP.
We are using the high speed SPI interface on pins P0.08...
