I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Hi
I have a question about using gazell link layer and paring library with concurrent timeslot api. I try to do this but i have the hard fault handler after invoked nrf_gzll_init...
HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I'm unable to import/export mesh networks and then subsequently send mesh messages. I believe this problem has been mentioned before [ 1 ][2][3], but the solutions offered...
Hi,
We've had a mesh sensor network all working for a long time using SDK17.0.2 + Mesh SDK 4.1.0
The data is accessed by a mobile app through a mesh node acting as a proxy...
Hey
I am struggeling to build the smp_server sample for the nRF5340:
west build -p -b nrf5340dk/nrf5340/cpuapp/ns -- -DFILE_SUFFIX="nrf5340_bt"
fails with a linker error...
Hi Nordic Team,
I’m currently using two standard nRF5340 DKs (non-Audio DK) running the nrf5340_audio application.
We’ve successfully adapted I²S speaker output on unicast...
Hello, I am going to use nRF52833 to develop a remote controller based on Zigbee RF4CE specification.
From the nRF5 SDK for Thread and Zigbee, it looks like RF4CE should...
Hello,
Is there a way to change the LPCOMP reference level in Zephyr other than what is set in the devicetree overlay?
I'm happy to disable it, change it and re-enable...
I am experimenting with the Nordic ESL sample application. The central_esl app is running on a nRF5340DK. I would like to add the nRF21540EK to this to improve the range....
I'm suddenly getting this error message with nRF Connect for Desktop. I've tried deleting and reinstalling, but the same error persists.
What should I do?
Error: Failed...
I'm not able to debug any of example applications that uses non secure build. Non ns versions works fine. I have added CONFIG_TFM_CMAKE_BUILD_TYPE_RELWITHDEBINFO =y to my...
Hi everyone,
I'm trying to interface the nrf5340 with the intan chip rhd2132, that allows to record signals. I can read successfuly the registers, but when I try the recording...
Hello,
We are using nRF54LM20A and NCS3.1.1 for our current product development.
we were using PDK/DK for our development and we got the datasheet "nRF54LM20A_Preliminary_Datasheet_v0...
Hello everyone!
I'm trying to get a custom board based on the nRF54L10 working. I am currently connecting it to my computer via a J-Link Edu and would like to get some basic...
Hi Nordic Team,
I am using NCS v3.0.0 and working on a Matter-based application.
I have enabled the ActiveHardwareFaults attribute (0x0005) in the General Diagnostics...
How can I confirm that an nRF52840-based device has been successfully provisioned? I don’t have physical access to the device, and it is running firmware that performs self...
Is there a sample app that uses the Zephyr Light CTL Bluetooth Mesh model? I've tried to add that model to the light_ctrl sample app, but get a crash during configuration...
