Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello,
I am building my own board with the nRF9151. I see that it can do SPI, but it does not say what pins are SPI capable. As the chip is a SoC (or CiP), can I use any...
Looking at the datasheet for the nrf54h20 it lists GPIO port P9 as Slow and Analog.
However, in the pin mapping, it also says SPIM130 and SPIM131 are available on port...
Hello,
We are trying to run 802.15.4 alongside our BLE Mesh network on the nRF54L15.
However whenever compiling with CONFIG_NRF_802154_RADIO_DRIVER =y, we run into the...
Our peripheral medical product, based on the nRF5340, is designed to pair and bond with both PC and mobile devices via Bluetooth Low Energy (BLE).
I've implemented BLE Security...
Hi,
I'm developing a custom MBR/bootloader for NRF52811 which is used as a second/radio MCU on the board. The MCU will need to run applications with and without the softdevice...
Hello,
I see that the nRF54L15 recently had a datasheet released at v1.0. Is there any difference between this and the preliminary v0.9 datasheet? I cannot seem to find...
Hi,
SDK 3.0.2, nrf9160 (actinius icarus som), custom board, based on modules example. LTE-M with PSM.
Floor current is too high, at around 500 uA. There is a known issue...
Hi,
I am looking to create use a pm_static.yml to create a partition table for MCUBoot, which have the internal flash as the primary boot partition and the external SPI...
I get this error after creating a custom board
C:/ncs/v3.1.0/nrf/subsys/mpsl/init/mpsl_init.c: In function 'm_config_clock_source_get': C:/ncs/v3.1.0/nrf/subsys/mpsl/init...
I'm attempting to put together an application using the baremetal version of NCS just released... I need these to run DFU over BLE so we can update in the field.
I created...
Hello,
I am experiencing a recurring issue when programming multiple nRF52840 boards using the nRF Programmer.
Problem description: When programming the first board...
Hello, I have a pin that controls the power flow to the sensors on my board. it is active low, when it gets a raw value of 0, it allows the power flow to the sensors. I have...
I have just upgraded my project to NCS 3.1.0 and I'm now getting this error
BOOT_SWAP_USING_MOVE (defined at C:/ncs/v3.1.0/bootloader/mcuboot/boot/zephyr/Kconfig:575) set...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
