Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
1. Using the nRF Connect SDK v1.2.0 development environment, nrf9160 developer, when testing connections to NRF_CLOUD in China, cannot be connected. 2. Please provide the...
1. Optimization is set to 0 flash read and write errors, set to 3 flash read and write correctly? 2. Please tell me what effect the optimization is on flash reading and writing...
Hi .
I am using nRF52840 dk in windows 10 environment.
I want to measure the RF output power of a single nRF52840 using nRF52840 dk.
I succeeded in generating a...
Hello,
On my custom board, on nrf52832, I can can use app_buttons for all usual pins, but not the XL1 (P0.00). I didn't try XL2 (not routed)
Using this pin as input or...
Hello devzone! I am using translation.
I'm trying various things in a continuation of my previous post , but I do have one question.
I set NRF_LOG_ENABLED to 0 at ble_app_blinky...
I've got an nRF52840 dev kit and am building my code using the app_ble_hrs_freertos project as a starting point. I'm building the .elf file, which I load into Ozone to do...
Hello everyone,
I hope that you are all doing well during those hard times...
I am writing a code for a nRF52840. The connection is successfully established with a cycling...
I have the NRF_CCM peripheral setup to encrypt packets on-the-fly. I can verify packets are properly encrypted when the payload size is 27 bytes or smaller. However, anything...
Hi,
I have created a configuration based on usbd_app_uart example where both usbd and softdevice are enabled on my device as soon as the device is turned on. When I transmit...
Hi,
I am developing a simple application that utilizes a light switch client example for NRF52832 with SDK15.0 and Mesh 4.0.
I am facing a problem when using the FDS module...
What could be the reasons that cause DFU Bootloader BLE not working with nRF Connect on PC (while it works with nRF Connect on iOS)? I have had various problem with nRF Connect...
Hello
I am using Seggar Embedded Studio for ARM V3.4 and nRF_SDK 12.3.0. I am trying to understand interrupts and interrupt handlers.
The interrupt request for Watchdog...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I have nRf52840 and I am trying to add a timer to examples\ble_peripheral\ble_app_uart...
Hi,
Setup:
I’m sending ble packages with around 80 Hz from an server (nrf52832 sdk 15.2) to a client device ( nrf52840 sdk 15.2)
One Ble package consist of several...
This is probably a simple question for an experienced nRF developer.
I have a demo going where I can read or write any of four characteristics I have set up on my peripheral...
