Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Dear sirs,
My purpose is to transmit stereo HiFiaudio from one source to two speakers wirelessly.
The speakers have their own power amplifier.
The problem is that the...
Hello,
I use NRF52810 with SDK 14.2.0 and softdevice 112. I need to use 7 input pins, but if I config more than 3 pins, all signals disappear.
GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS...
Hello all,
SDK:S332 V4.0.5(related to BLE V4.2).
Platform:NRF52832.
For improving BLE data throughout, i tried to set some configurations by other guidance.
Following...
Hi Tech Team,
I am using nRF52832 chip and the recent soft device(SD). I want to implement my own file storage and thus using sd_flash_write () and sd_flash_page_erase functionalities...
Hello Nordic experts,
I am using nRF52840 and SDK 15.3.0. I have added an OUT ENDPOINT to the usbd_hid_generic example by following the suggestions in https://devzone...
Hi,
I'm new to programming and I can't seem to solve this error of "No such file or directory" even when I already put the file in the location of the directory.
How...
I am writing a 1-wire driver (there doesn't appear to be one in the SDK), and am looking at dynamically switching the GPIO between read/write. There appears to be two functions...
I am running the light_switch example and it works fine works fine , I am using the nrf_application to configure the nodes.
I am using latest mesh sdk and 15.3 nrf sdk....
Hi guys
I had to integrate a CLI module into a project I'm working on, that is running FreeRTOS
after quite a lot of work, I managed to get this working, but seeing...
HI,
I am using nrf52832 dk. I have a sensor that gives a negative voltage. I want to measure the value using saadc.
and can I use differential mode saadc for negative...
Hello All,
I am working on the N51822 custom board.
Using segger IDE, SDK 12.3
Previously i have worked on the sdk 14.3 on the n52810 board. It is working properly...
Hello
I am using pin 1.15 of nrf52840 dongle with transistor with enable pin of another chip. The other chip is a wifi chip which I only want to switch on whenever I have...
Hi All
I am using nRF9160 DK version 0.8.5, and I have gone through this link, downloaded and Installed all the steps, given there. All seems to be running good.
But some...
Hi I am using the custom_bluetooth_service tutorial from https://github.com/bjornspockeli/custom_ble_service_example with SDK v15 and nrf52840 DK.
I am now trying to use...
Win10 + Segger embedded studio
I can get the pca10059 blinky example to work. ( C:\nRF5_SDK_15.3.0_59ac345\examples\peripheral\blinky )
I use the NRF connect Programmer...
