Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hello,
we want to send a continous carrier with nrf9151 on dect-nr+ on a specific channel.
With bluetooth there is a testing option in nrfconnect tool.
Is there any...
Hi I would like some advice on where to start learning Nordic BLE?
All I could find by searching was advice from 6-9 years ago, I think today they are not relevant, because...
hello,
I'm doing a power consumption test, but I'm not sure which project to use to test the power consumption.I tried the "peripheral_lbs" download with NCS version 2.8...
My setup: SDK version: 2.5.0.v Modem version: 1.3.0. I am using MQTT to subscribe to a topic, for example, the LED state. The plan is t o set the LED state on the server side...
Hi,
The SDK version I am using is 2.6.1 and the example is "matter lock".
I wrote the following configuration into \child_image\mcuboot\prj.conf.
And add the code...
Hello, thanks for reading and happy holidays!
We are using an nrf5340dk, with zephyr and SDK 2.5.0.
We seem to have two undesired behaviors from MCUBoot immediately after...
Can,t flash nRF52832 custom board using nrf connect vscode extension im trwing to use nRFconnect for my project, im using fade_led from example and got this error
i try...
Hi everyone, I have a problem when I tried to configure UART ( baudrate, parity, data_bits, stop_bits, flow_ctrl). I upload my project:
#include "myuart.h"
#include...
Hi,
I want to use nRF9160's internal RTC. I coded it but did not get the real time correctly.
SDK: 2.5.0
IDE: vs code
board: nRF9160dk
Best regards,
Liza
I'm going through the Academy courses and somewhere around Lesson 3, I could no longer flash firmware to the nrf52840 DK.
I browsed the forum and found some notes around...
nrf connect for desktop nrf54l15 device not detected by bluetooth le app
log:
12:18:38.872
Using nrf-device-lib-js version: 0.4.4
12:18:38.872
Using nrf-device...
Hi,
in Cellular Iot Fundamentals there is in lesson 4 an exercise to move to MQTT with TLS.
As I used MQTT helper library, I wonder if it is enough to modify the structure...
We had an issue with the FDS such that if the device lost power in the ~50ms window after bonding was carried out, the FDS would take longer to initialise when power was restored...
Hello,
I have read conflicting information on whether Verizon requires the LwM2M library to certify on their network. We will be certifying a nRF9151 modem.
This Nordic...
