HI,
I want to use PWM to control various hardware (LED's, etc ..) so I started off from the suggested PWM code example, found in this forum + modified it as I want to use...
hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
I am using flash_fstorage_s140_pca10056 example from SDK v17.0.2 , I see that the start address is 0x0003 E000 and the end address is 0x0003 EFFF respectively.
I want to...
Hi,
I am trying to check how DFU works but I have problems setting it up. I will describe all the steps that I have been doing here, so that it will be easier to try to...
Hi, I am designing a custom board usign the NRF52832. Im using this externar crystal https://es.rs-online.com/web/p/unidades-de-cristal/1753468/ . but I have seen that many...
Hello Nordic Support Team
I need desperate help to get my proof of concept working. I have been able to prove that the applicational concepts work on the nRF52840 and now...
I'm trying to create an application on the nRF52840 that can read serial input from an external GPS chip and also provide log output via USB. As I understand it, the UART...
I want to read access address of a connection between master and slave in master.
I need access address and not the MAC address after connection establishment.
Is there...
Hello, when developing our application, we run into a problem. We are running Zephyr 2.4.0 on nRF52840 MCU. We use LSM303AGR sensor, which is supported by zephyr LIS2DH driver...
Hi,All:
1. As the topic, now i just make bootloader,How do i perform a app entrance? and how to staging, combing.........in the picture as below. Or,on the other hand,how...
Dear,
I am trying to manually toggle GPIO0_2 by writing into the GPIO register, 0x50842504[bit 2]. The output of GPIO0_2 was always static in either high or low.
If...
We use the Nordic library for mesh with Gatt proxy service to our mobile device. We've noticed that unsegmented messages are only serviced and sent every 250ms through the...
Hi, I have made a super hex file and getting the following issue. I have already made a super hex file successfully already but this time getting this error. Does any solution...
Dear friends,
I want to store the sequence nunber in flash, from the case we can know the mechanism.
I found a strange phenomenon that I flashed a serial example( nrf5_SDK_for_Mesh_v5...
Dear friends,
I used my nRF Mesh app provsioning a new device, now, I can export the Json format configuration data of the Mesh network from nRF Mesh app, I want to use...
Hi,
On button press, the button handler event calls the "ble_lbs_on_button_change" function which sends notification to the BLE client.
The value of the button state...
Hello Nordic support,
I am developing a Zigbee application based on FreeRTOS for a device with coordinator role. I was able to add the Zigbee stack and start the Zigbee...
