Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I have installed from "nrfgostudio_win-64_1.21.2_installer" on Win-10 laptop. Weh I start nRFgoStudio, the main window appears for a second then I get a message "nrfgostudio...
Hi all, we're using code from this forum to enable GPIOTE and PPI to measure the low between the arrows to indicate a "start of transmission" and then switch to measuring...
Materiel and software use :
SDK mesh 2.0.0
SDK 15.0.0
NRF52832 with PCA10040 x5
Situation :
I would like to implement this network :
I follow the instruction...
I'm using the UARTE peripheral via the UART driver code in SDK v14.2. Due to transfer size and SoftDevice timing I have to use the double-buffered receive method (by calling...
Hello,
I am trying to make a beacon start advertising on a long press of a button. Using this as a reference, I implemented a timer as follows:
this is the flag to keep...
Hi!
I am using SDK15, my application is based on app_ble_uart. I have added my proprietary characteristic to NUS next to RX and TX Characteristic with quite a success. Now...
I use sdk14.2 nrf52832 as the primary, connect two iphone peripherals, iphone is connected to broadcast, when I turn on both peripherals, sometimes everything is normal, sometimes...
Hi
I am a beginner to BLE based products, i bought the nRF51822 devices hoping to create a mesh network. The problem is i have got the development boards but i am not able...
Hi there,
I'm new to Android BLE development and simply trying to read out a BLE temperature sensor that encodes the temp. in the service data from the advertising packets...
Dears,
Can I know NFC Tag memory size?
In case of NFC record_url, total flash size is 13.4KB and ram size is 17.9KB to use SDK15.
I am curious to know the memory size...
Dear Nordic Team,
We are currently evaluating the nRF52832 / nRF52810 for our product, a solar powered wearable designed as part of a safety system in the sailing sport...
My Setup: -> OpenWRT Chaos Calmer 15.05.1 -> Kernel - 3.18.23 -> MCU - nRF52832 Custom Board -> SDK - 15.0.0 -> IDE - Segger Embedded Studio
I am able to start a 6lowpan...
Hello,
I would like to know from were i can get release history for Nordic device family pack.
I can find Zip file for downloading different Nordic family packs but wit...
We want to support low power end device sleepy so do the MESH SDK 2.0.1 has the support of Friend and low power mode support in mesh SDK? I'm using nRF51822 SoC .
