Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hello everyone,
I am working on a project with a Thingy91 that has an nRF52840 and an nRF9160 , and I am trying to read the battery level. I want to measure this battery...
In ticket Case ID 290251, Torsten Rasmussen provides the following advice to ensure that the toolchain corresponding to the SDK is used to build the SDK (this applies to nrfutil...
I am lab testing Nordic's DECT-NR+ (DECT) for a new factory automation application; I am using the hello_dect sample application from the PHY webinar demo, I am trying to...
I made a custom board, uploaded the Arduino bootloader and was flashing the firmware with Arduino I used it without any problem with revision 2 But when I use revision 3 chip...
Hi! I'm working on the firmware part that needs to perform operations on the same variables both inside GPIO IRQ and the software timer callback. So, there is a need for a...
Hello, I want to send data from peripheral devices to central device. My peripheral device code is based on "ble_peripheral_uart" sample and my central device code is based...
Hi, I'm working on developing a UWP app that can detect any or compatible Nordic devices. let's say a device has BLE capabilities, then through the desktop app i should be...
I have both a nRF5430DK and a nRF9151DK (or 9161). If I wanted to develop a solution with both BLE and LTE, how do I set up a DK environment for them to work together? Do...
Hello,
In my experimentation to update advertising data during runtime, I am following the example @
It is using the ble_advertising.h library module
However I would...
Hi,
I am using BM840 BLE module and I see after integrating the DFU application, the main application is not executing at all.
When I try to debug, I see it is not coming...
Dear Nordic Semiconductor Support Team,
I am conducting academic research with the nRF52840 development board, specifically investigating the use of SRAM Physical Unclonable...
HI Sir/Madam
I downloaded SUPL-C sdk 0.7.2 ad I add the following variable to the prj.conf
#SUPL client library
CONFIG_SUPL_CLIENT_LIB =y
CONFIG_GNSS_SAMPLE_ASSISTANCE_SUPL...
We have our custom NRF52840 board but never used BLE communication. We have an application where we need to send data to SCADA wirelessly. We have programmed our UART to receive...
In my application with nRF5340 and nrf connect sdk 2.3.0 which works well as Peripheral, if I activate CONFIG_DM_MODULE=y I always get the error "...ld.exe: region `RAM' overflowed...
I had an opportunity, to do a complete pristine reinstall of Windows 10, and to then do a pristine install of Visual Code, nrf connect, etc.
After doing that I did this...
