Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
I'm attempting to troubleshoot a system crash when polling a sensor at higher ODRs while BLE is enabled. I'm using NCS v2.9.0 with the nRF54L15. I checked the thread stack...
I'm trying to compile the lsm6dso example for a nrf5340. I also tried the nrf52832, but I get the same error.
v2.4.2\zephyr\samples\sensor\lsm6dso
prj.conf:
CONFIG_STDOUT_CONSOLE...
Hello, i'm considering an application using nRF52840 in following configuration:
- I2S RX would be connected to some external I2S source (I2S slave)
- I2S TX would be...
Hello, I'm trying to make a application bootable through MCUBoot but I'm having a hard time generating the .bin file with MCUBoot header. According to this page I should be...
Hi I want to use nrfutil nrf5sdk-tools in MacOS but when I try to run it I get the following error.
" Error: Failed to spawn inner nrfutil-legacy executable
Caused by...
We are trying to update the SDK used by a firmware on a device that is in production. The old SDK is 2.1.0 and we are trying to update to 2.9.0.
I was able to get the firmware...
i am currently using nrf52840 dk as a hardware, nrf5sdk version 17.1.0 ,ble_app_uart peripheral example (s140 soft device )
here the maxmimum mtu is set to 247 bytes whether...
Hi everyone, When I try configure UART (parity, data_bit, stop_bit, flow_ctrl), I have noticed error when I run in terminal: "
*** Booting nRF Connect SDK v2.9.0-7787b2649840...
Hello
I am developing an application based on the nRF9160, it uses Coap protocol to connect to nRFCloud to transfer the data. Also I have implemented the FOTA which always...
Hello,
I am using the nRF52810 with SoftDevice S112_nrf52_7.0.1 and trying to create a simple program that sends the character "1" to a mobile device. However, I am encountering...
I've been having trouble downloading the Connect SDK in VSCode, so I want to download the SDK from GitHub first and then import it into VSCode. How can I import the SDK I...
Hi all ! I'm new to the nRF MCU, I'm aiming to use one for a school project.
I've bought the devboard (nRF5340-DK) on a known website (Distrelec.fr, part of RS groupe)....
Hi im having problems with restarting advertising after disconnect. I tried NUS example, simple peripheral example but none of them works.
I modified NUS example with some...
NCS 2.9.0
Adding mcuboot to sysbuild and using "sysbuild/mcuboot.conf" works as described in Academy exercise-1-configuring-extra-image .
But if I want to use a board...
I am working on the ZigBee communication my device is working fine but i got in to the issue when i tried to use custom cluster all the resources, i found online are more...
