Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Dear Team,
We are developing a product based on ble mesh. We are planning to select NRF52840 as master device and nrf52832 as slave device. Slave devices should be more...
In the ble_app_beacon example in nRF SDK 17.02, there are two defines namely APP_BEACON_INFO_LENGTH (0x17) and APP_ADV_DATA_LENGTH (0x15). The former defines length of the...
I am trying to port some code from the nrf52840dk (PCA10056) to the dongle (PCA10059) and everything seems to work fine until an interrupt is triggered. All serial output...
Hey! I have a project with custom board with nRF52833 and I would need help with just getting data from sensor via i2c and sending it via bluetooth to mobile device. For some...
Hey!
I would like to use the nrfjprog executable from the nrf command line tools for flashing the nrf9160 modem firmware. I read some older tickets about this issue and...
I have a requirement to start the MCU with extended non connectable advertisement for few minutes and then activate normal connectable advertisement for another few minutes...
Hello,
We have an app_timer that runs periodically for the application, and we are also using BLE peripheral code. Once the application timer expires, the event handler...
Hi,
The Dongle was given to me by a colleague of mine who has the exact same laptop as I do. The Dongle was and is working fine with his laptop. The problem is with my office...
Hi ,
i am using nrf52832 soc with customize board trying to optimize the power the following events occur:
1)The first time when i code uploaded it initialize all the...
Hi,
Is there a way to set somewhere in the softdevice or a library to automatically disconnect after an idle connection? Idle means, nog characteristics being read or written...
Dear Nordic,
I have some questions when study the usb audio of nRF52840;
What function when running the nrf_drv_usbd_errata_104 function?
Do I have run it? Can I remove...
Hi,
I am struggling to find a basic sample for UART communication in NCS. As an experienced Nrf5 SDK programmer, I find it very hard to convert my firmware to nRF Connect...
Hi Nordic Support
I have been experimenting with your nRF52840 board there has an SPI flash and have tested it with your USB example that can enumerate the filesystem on...
Hello,
I have the following setup:
a computer connected to a PCA10040 over USB
a PCA10040 connected to a NRF52832 over SWO (SWD IO, SWD CLK, SWO, RESET).
I would...
1. I am using the nrf52832 at the transmission side (ble).
2. at the scanner side I am using the ESP32.
3. I want to display the "advertising device name: " at ESP32 side...
