Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am trying to use the mpsl_radio_notification_cfg_set() API function to configure a radio notification. However, calling the function returns -115, which is (NRF_EINPROGRESS...
Hi:
We are develop an Central Device can Connect 8 BLE Device in same time. and want max throughout. it use queue and freeRTOS. the Central TX is simple.
use sd_ble_gattc_write...
After successful compilation of code the west flash command shows this output after using Tag connect to debug the icarus board with the nrf9160 development board. Normally...
Hi. I know this issue already point out by some of the developers. But I don't get the right way to generate a hex file for my client.
I select the Release on the top right...
When using the local timer of the SAADC it should be started with TASK_START according to https://infocenter.nordicsemi.com/topic/ps_nrf52840/saadc.html?cp=4_0_0_5_22_4#concept_continuous...
Hi there,
I'm interested in using LittleVGL (lvgl.io) for my project. There is a LittleVGL example using nRF52840 in Zephyr project, but no in the nRF Connect SDK. Are...
I have successfully implemented the meander PCB antenna outlined in this app note, however, I am looking for and cannot find information on a shrunken version of this antenna...
I am trying to create an AOA link sending a CTE from an nrf52811 (BM833A module) and the receiver with an nrf52833 (bl653 module). Analyzing the CTE detection data, the first...
Hello guys,
I've a PCA10040 connected to my laptop.
It works fine with all the .hex BLE template example in the nordic SDK except with the UART example.
After download...
Hello,
I was using the usbd_ble_uart code for the nrf52840 dongle. When I connected the dongle to u-link 2 debugger and used keil uVision I was just doing my settings in...
NCS version：v1.5.1
board：nRF5340DK(0.11.0)
first，i use SES Embedded open radio_test project and choose nrf5340dk_nrf5340_cpunet ,and use [west flash --erase] download...
I am using nRF Connect SDK Tutorial - Part 1 | NCS v1.4.0.
I am using MacOS and nRF Connect SDK v1.6.1 .
a. The JlinkExe executes but JLinkRTTClientExe doesn't show any...
