I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi, I am trying to get the voltage level of the battery using the AT_command AT%XVBAT which I tested using the at_client sample. I tried integrating it with my current code...
From looking at the code when a message is posted to "all-nodes" fixed group address of 0xFFFF it does not route. I was unable to find this behavior specified anywhere in...
Hi forum,
I am working on nrf52832, using sdk 15.0.0. I want to send the data(command) from esp32 to nRF52832 through Rx ,Tx . I have done connections rx,tx,gnd . I can...
Hi,
We are developing our stack with soft device using nRF52840 as the Controller and have the below queries
1. How to configure a static random BDADDR which will remain...
The error is
CMake Error at ../../../cmake/extensions.cmake:416 (add_library):
No SOURCES given to target: drivers__spi
This similar to
https://devzone.nordicsemi...
Hello everyone,
Hello everyone, I am a beginner in programming with OS based systems. I would like to get more into development with the Zephyr based NCS. For now, I want...
Hello!
I try to run FatFS example (SD card example, pca10040) from nRF5 SDK on my nrf52832 (ebyte e73) with microSD card with no success. No matter what I'm still getting...
Hi,
I am trying to get the time and UNIX time after LTE connected. but getting 0 only.
please log
date_time_update() function does not support in SDK 1.4.2 so I...
Hi,
In "nRF52832 Product Specification v1.4, it recommends 32MHz with 40ppm as below:
as the question mentioned above, can I use one with 10ppm?
thanks
best regards...
Hi,
I am getting assertion failed error when putting the device in System off. Could you please help me understand why?
Below in the code where the error happens:
...
I'm working on modifying the ble_app_uart pca10040_s132 to send strings stored in flash memory over BLE to the nRF connect app on an iphone. From what I understand the uart_event_handle...
Hi There,
I m trying to use the xxxx\SDK's\nRF5_SDK_for_Thread_and_Zigbee_v4.1.0_32ce5f8\examples\peripheral\spi with the nRF52480 Dongle and I already had applied the...
Greetings
I have an NRF51422 QFAAEO running S210 Soft Device version 3.0.
I have written a Bootloader application that uses Ant-FS as the upload mechanism. During testing...
Hello everyone,
is it normal behaviour to lose data on UART reception when BLE scanning and advertising both are active?
So far I didn't lose serial data if I just run...
hi all.
I am trying to change number of data packets in one time interval.
I don't know the senario to change it.
For first step I wrote this code to change the quee...
