Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Hi all,
I need to directly develop my application on top if IEEE 802.15.4 MAC layer. Could you please inform me of any sample application available under Zephyr that directly...
Device: nRF52840
SDK: 16.0
Softdevice: ANT_s340_nrf52840_6.1.1
Hello, We have a master and several slaves setup in a simple master/slave channel configuration. It seems...
Hi,
Can u suggest the procedure to implement key refresh procedure with the sample network using nrf mesh app.
No where i found option in nrf mesh app.
Thanks in Advance...
Hi,
We have 2 projects in pre-production stage that use nRF52840. We are also using FreeRTOS for both projects.
Now we need to create an OTA bootloader for both. There...
SDK: 17.0.0
Hardware: E-Byte E73-2G4M04S1B module
Chipset: NRF52832 QFAA QFN48
Running the hids examples, I noticed that the hids_mouse example will go from Fast Adv...
Do I need to carry out ANSI C63.27 regulatory test for coexistence of wireless communication that share the 2.45GHz band if we designed a custom PCB BLE antenna for NRF52840...
Hi,
I have the nRFgo Starter Kit with the radio module (nRF2427LE1) attached. First, does the radio module not have a bootloader already downloaded to it? Next, when I...
Dear Support Team.
We want to support secure DFU on mobile and desktop platforms. Do you have any documentation to implement this on Mac OSX and Windows?
Its an open...
Hi, is there any LE audio sample for NRF5340?
I know the upper layer protocol is under developing on Bluetooth SIG, but is there any possible way to direct use the HCI command...
Hi
I'm developing with nRF52832.
I am using Segger Enbed Studio as a development tool.
When you download a program from Segger, Segger does reset once, and I wonder...
Hi,
I want to run QSPI application example on my nRF52840DK (PCA10056) board with logs seen via UART. I successfully uploaded QSPI bootloader example and Blinky SysTick...
Hello,
I'm developing an BLE application with NCS where I want to be able to change the BLE device name during runtime. Therefore I enabled CONFIG_BT_DEVICE_NAME_DYNAMIC...
Now we development a switch and use it control the light. When i push switch close the light, there was still a faint light. Then i found when NVIC_SetPendingIRQ(EVENT_IRQn...
What I intended was to write x'700' to x'10001080' i.e. NRF_UICR->CUSTOMER[0] !
When ran my application, which outputs NRF_UICR->CUSTOMER[0] to the log, I was very confused...
In firmware I can read the programmed UICR serial number as follows: -
uint32_t serial;
memcpy(&serial, (uint32_t*)0x10001080, 4);
Is it possible to program the UICR...
