Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hello, I have developed a program that reads (with I2C) a temperature sensor and sends it to the central board. The central board is a NRF52480-DK. I have tested the peripheral...
Dear Sir.
I was testing dfu mode with an nrf52840 dk and held down the IF BOOT/RESET button, then powered up and waited a few seconds before it went into bootloader mode...
Hi,
I'm evaluating the NRF52832 for an ultra low power BLE application where I'm going to use GATT. I've built some prototypes with the NRF52832 and right now I have to...
Our engineers have two questions that they are confused with:
1) When applaying ble techniques, does nodic 52 serious of chip compatible with SIG mesh?
2) When applaying...
Hi there,
we are working on getting type approval certification, and the test lab is asking for fixed frequency software, drivers and SOP.
What we need is the fixed frequency...
Hi,
The actual problem: I want to store some stuff to flash at factory, that is never erased. And I also need another persistent memory that can be written in runtime. I...
Hello I am now trying to implement an active NFC Tag using nRF52832. But I don't know what that example project is. Can you point to a command or example source that performs...
Hi,
nrf-sdk: 1.3
Firmware: 1.2.1
Using offloaded sockets(secrets at the modem side)
My use-case is this: Provision PSK and identity to device at the factory for DTLS...
Hello,
do you have any method, example or other documentation to recommend to me in view of implementing the storage into non-volatile data with our thingy91 ?
we use...
Hi team,
Is it possible to route the low frequency clock inside the nRF9160 to an external device? If not, then the only option is to generate the clock using the timer...
Hi,
We use the nRF radio timeslot API to take control over the radio and other peripherals periodically. We have noticed that when the timeslot is active (we own the peripherals...
I tried to use the Bosch BSEC library for the Asset Tracker application for nRF9160.
It seems that the Asset Tracker was build for BSEC 1.4.7.4 which is unfortunately no...
I develop a test fixture based on nrf51 code that I use for final product.
NRF51 is just a part of a complex test fixture, then I have just "one" test fixture model.
I...
Does m_xfer_done need to be set to false before calling nrf_drv_twi_rx? If so, does while (m_xfer_done == false); loop need to be called on every read?
