after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi everyone,
we are using nRF52832 with SDK 15.0.0.
Our device uses one central and one peripheral simultaneously that are running independently. Recently, I've faced...
Hello
I am trying the UDP example, but I can't find the IP address and port number of transmission, also I would like know how to view the code of functions and libraries...
hi.
As the manual says,It waits for an application event. and is called in the main while loop.
Does it mean that if I put some other routines carrying out polling function...
Hello, I am interested on nordic devices that support: 1) 802.15.4 (eg. Openthread) 2) secure storage for storing keys (e.g LWM2M credentials) 3) zephyr - rtos
I have seen...
Hi, we have a nRF9160 DK where we have uploaded the AT_CLIENT example on. Have tested the board and it works fine, able to send AT Commands and join to the network etc......
Hi,
I want to store scene when long press one button and recall scene when short press. I have done some changes but not able to achieve it, i am not sure if i should...
I was looking at this compatibility matrix, for SD and SDK.
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcomp_matrix_nrf52832%2FCOMP%2Fnrf52832%2Fic_rev_sdk_sd_comp_matrix...
Greetings!
we are using nrf5340dk to communicate with a Nucleo shield that has LIS2DW12 accelerometer on it (shield is X-nucleo-IKS01A3). We have a problem communicating...
Hello, I'm beginner for nRF52.
I saw examples about entering DFU by button and buttonless.
Is it also possible that changing the boot mode by a gpio pin which controlled...
Hello all, I'm working on ADC and data transmission.
Device do ADC first, and send those values.
Sampling frequency of ADC is ~80 kHz (sampling per 13 microseconds), and...
Hello,
We are using nrf52805 for our project. Facing some errors like "GATT ERROR" and GATT INSUF AUTHORIZATION and GATT CONN TIMEOUT ERROR" when I want to upgrade my application...
Hi,
We are developing our product based on nrf52382. In the scope of the certification testing of our end product, the test laboratory asks me if the Bluetooth low energy...
I am currently building a dynamic multiprotocol application (Thread+Bluetooth LE) with the nRF Connect SDK. For tweaking coexistence I would like to limit the length (=duration...
Hi,
In nwp-036 page 7,here is the AOD sketch map as below :
As fat as I am concerned, the Transmitter and Receiver should be reverse ?
Or there is something I misinterpreting...
Hi,
Background: I am looking at interfacing nRF21540 (FEM) with nRF52833 (Host) - hoping there's Zephyr support available for this(?)
Question: Product spec for nRF21540...
