Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I am working with a Blend Micro Board (Arduino IDE with RBL_nRF8001 sdk), using
Evothings.
Using the RedBearLab Simple control example I can easily connect to the board...
Following this tutorial : devzone.nordicsemi.com/.../
I type 'make' and it compiles for a bit and then I get a bunch of errors that say this:
[278]: *** [_build/nrf52840_xxaa...
Hi all,
I measured the delays between a GPIOTE event and a Task (in this case toggling with another GPIOTE) through PPI.
The results are showed below:
For the...
Hello, I followed from the link . I successfully program bootloader, and bootloader setting and program. And my program is working fine.
But I cannnot update from DFU. Everytime...
Hi,
I am working on with nrf52 with SD132 v2 SDK11 since we need serial bootloader.
I tried a gattc long write sequence to write 22 bytes. Everything works well, peer...
OpenThread recently merged a DNS client into the main branch. DNS would be extraordinarily useful because my code accesses content behind load-balancing servers with dynamics...
In this example code:
nRF5_SDK_13.0.0_04a0bfd/examples/ble_peripheral/ble_app_proximity/main.c
Where the ADC is configured to read the battery voltage:
nrf_saadc_channel_config_t...
Hi,
I've read a couple of threads in this forum that suggested that the DEVICE_MANAGER_APP_CONTEXT_SIZE value (which should be a multiple of 4) is supposed to be 16 bytes...
We're using the nrf51 with the RFAxis (now Skyworks) 2401C amplifier, which is a fixed gain 20dBm amplifier. The goal is to have a longer range 'beacon' type product and the...
What would be the best BLE Library or Framework for Raspberry-pi to exchange with nordic?
I'm trying to get data from the NRF51's GATT data.
But there are no reference...
I recently was trying to test my nrf52 DK. After lot of failed attempts i was able to do DFU update over BLE and also Serial upload .
I am now trying to test the BLE UART...
Hi
According to previous answers ( 1 & 2 ), the limitation on the maximum number of devices that can be added to a whitelist is 8, and is due to softdevice timing limitations...
I have downloaded the nRF51 SDK from here www.nordicsemi.com/.../nRF51822 and I'm trying to run HCI-UART examples as explained here developer.nordicsemi.com/.../a00063.html...
Hello,
I use SDK 13 on nRF52832 with a SD card (nRF port of fatfs lib).
I have a long sleep and i want to minimise current.
With SD card, it's okay i switch off SD...
Originally, this was a complaint about SIGTRAP 0xffffffe while using GDB.
But I've discovered the actual issue is related to a lack of erase/programming of FLASH.
My environment...
