Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
When I download and install NCS2.8.0 SDK, I want to build matter project(ex: light bulb), do I need to install matter build environment referring this link( matter build ...
Hi,
I'm using NCS version 2.7.0 with nrf9151dk. When I tried out the nrf cloud multi service project with hard coded credentials as explained in this document nrf cloud...
Hi Nordic
I had used toolchain manager to download and install previousl ncs versions. Everything was fine.
But, as installing ncs2.9.0, at the end of installation, it...
When I recently tried to write a Gazell project using the nRF Connect SDK, I found that many files referenced the `nrf_gzll.h` file, but I did not find it in the nRF Connect...
Hello everyone!
I'm designing a flexible PCB and I'm a bit confused with the stack up. I've seen that the nRF52840 development board has an NFC antenna with the following...
Hello !
I'm wandering what is this warning when building the sample for the nrf54L15dk :
unit address and first address in 'reg' (0x5004c000) don't match for /soc/peripheral...
I was reading the documentation, trying to figure out something specific while reading though source code. I was looking at the LENGTH field specified in the nrf52840 PS guide...
I'm looking for a correct way to define partitions for my app + mcuboot. Here and there Nordic says that when using MCUboot, the partition manager is used instead of device...
I am experiencing weird radio core boot behavior after switching to SDK v2.9.0-nRF54H20-rc1.
First I followed the bring up guide for SDK v2.8.0, flashed latest BICR for...
Hi,
I am using the nRF54L15-DK and nRF Connect SDK v2.8.0 Zigbee-Addon.
In an environment with three devices: Coordinator, Router, and End Device,
When powering on...
Dear Nordic Technical Support Team,
Hello!
I am currently using the nRF52840 DK and have implemented SRAM PUF. I would like to connect the development board via USB and...
Hello,
I am using the nRF Connect for VS Code plugin with my codebase, which has multiple applications. I added a build configuration and specified the build folder to be...
Hello.
I am developing using nRF5340DK and nRF Connect SDK v2.9.0. A fatal error occurred on the board when sending some Mesh Model Messages to the smartphone app. It doesn...
Dear Nordic support team,
We are evaluating a new project using nRF54L15.
Please provide a SDK to us for some estimation (mainly memory usage).
The following features...
