Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Hi All,
I am an electronics engineer but new to nRF51822 programming. I have used the PCA10000 & PCA10001 using Nordic SDK, using nRF Studio etc. In nRF Studio, you can...
I'm using SD110, and in my application I have an array of 64, 32-bit integers.
Typically, the client will only need to read 1 of the 64 values, or write to one of the 64...
I'm just getting started with the nRF51-DK, and I'm still confused about which SD I need to load, and which roles I need to support aka GAP and GATT.
My end application...
Hi,
It seems to me that pin assignment and package is the same for both nRF chips. Can I solder nRF51422 chip instead of nRF51822 for ANT testing purposes on my PCA10004...
Hello,
I have a custom board (was built using the Nordic schematics provided with the Smart Beacon Kit). I am using J-Link LITE to try and program the board.
The board...
Today nRF Toolbox App on my Android 5.0 phone is only recognizing HRM code running on my nRF5182-mkit, not other examples.
Today nRFToobox and nRFUART2.0 Apps both...
Hi,
I hope use nrfjprog.exe to do following things:
HW: nrf1822
download s110 6.0
download bootloader
download firmware
write some values to certain addresses...
Hi,
I've tried to search the documents and the forum for an answer to my question, but didn't have much luck.
We have a custom board that uses a STM32 micro and nRF51822...
Hello,
I am currently trying to find out how the BLE devices keep their connections in sync. According to the spec, the peripheral can have a slaveLatency of up to 32s...
Is it possible to run Master Control Panel and the PCA10001(or the J-Link lite) at the same time on the same PC, or will that cause problems? I guess I could simply try it...
Hello, Can anyone point me if the nRF51 Dongle can be used for connecting the device with an Android mobile.
Have used this dongle for connecting with PC opening COMM port...
Hi,
When pointer the p_conn_params of ble_conn_params_init_t to NULL for ble_comm_params_init(),
the connection will be disconnected fast automatically, test with the...
Hi,
I am using custom nrf51822 board. I am trying to debug through JTAG(segger j-link). While downloading the program into flash, I am getting error like "Error: Flash...
There can search for profiles using the search method of Bluetooth 2.0 (RFCOMM) connection is not a state in the PC Settings in Control Panel, why Bluetooth 4.0 (GATT) is...
hi guy.
i'm developing such a joystick device Board(HID) using nordic nRF51822, BLE mode.
i have tested many android cell phone & pad and i didn't have connection problem...
