Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
This is the normal kconfig menu.
But it often happens that the following picture does not recognize anything in kconfig
and there is no devicetree option in the action...
Hello Nordic,
We developed our product using MCU NRF52840-QFAA-F-R. Our client is based in the EU. We plan to launch our product in 1-2 months.
I have a few questions...
Hello,
I am working on a prototype Bluetooth Low Energy module using the MDBT50Q-512K (by Raytac).
To measure the frequency of this prototype with test equipment, I am...
has been helping me connect to a device and I am finally able to do that, but as soon as I do, Zephyr crashes.
This is with a lightly modified central_uart project [00:00...
While creating a new board in step 2 of the exercise, there are a couple of problems with the sub-steps 1-5:
First, sub-step 1 says to name the board "DevAcademy nRF52833...
Hello,
I've been using the libuarte module in my project, and I done a power consumption reading. With libuarte switched on I'm consuming 0.78ma, and with it switched off...
We have been seeing a bootloop issue on some of our nRF52840 boards running NCS v2.6.1 using CR2032 coin cell batteries. The batteries are all around 3V.
This is an intermittent...
ON NCS SDK 2.7.0 version, how to calibrate SAADC?
I checked below code, I see that "Perform calibration before the reading is taken if requested.", it will trigger calibration...
I am developing a product for a customer using NRF9151(ncs2.7.0, modem fw: mfw_nrf91x1_2.0.2). While verifying it on the DK board, I discovered an issue. When the system starts...
Hi!
I'm writing new firmware for the nrf54 family, and I want to have a system timer with 1s resolution (clock). This clock will be occasionally synchronized with epoch...
I am currently working through the Nordic Academy - SDK Intermediate Course - Lesson 2 Exercise 3, found here:
academy.nordicsemi.com/.../
I am not seeing any of the...
Hi,
Going through the nRF Connect SDK Intermediate course on Lesson 2 exercise 2 step 9 there is a command ncs_install_path/PathToToolChain/opt/zephyr-sdk/aarch64-zephyr...
Hi,
I've recently brought up the Matter Test Harness on a Raspberry Pi following the instructions in the CERT tool repository ( https://github.com/project-chip/certification...
I know the default answer is no, stopping nrf24 and get a RF52 or nRF53 series but my question is about an existing product. We are not all FORD, we can not just do a mass...
Dear Nordic Support Team,
I'm currently working with your Flutter library, mcumgr_flutter version 0.4.1, to implement Device Firmware Update (DFU) functionality. However...
