after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
My ultimate goal is to add NDT [1] to a meshtastic [2] device implemented with RAK4631[3]. For this goal I can see the following obstacles:
- The meshtastic stack...
Hi,
I am trying to modify the ble_app_blinky example in such a way that I can connect with multiple central devices to on peripheral device.
So far I found a good start...
From "nrf_section.h" (__GNUC__):
Example for the section name " log_const_data ":
NRF_SECTION_DEF(log_const_data, nrf_log_module_const_data_t) //: extern nrf_log_module_const_data_t...
I am using NCS Connect SDK version 2.6.0
I am trying to create an array of models and found a problem with using Zephry macros in C++ projects. My main.cpp is as below ...
I have a sample app (hellow world from the zephyr samples).
It compiled well on my system in vscode using 2.7.0 and sysbuild.
I then installed 2.8.0 and suddenly the build...
Hi,
I just got nRF54L15 Development Kit boards. I installed 2.8.0 nRF Connect SDK and toolchain into VS Code. I was using 2.6.1 versions,
with nRF52840 and nRF5340 DK...
Am making a project based on NUS central demo and I can connect to our remote unit with the 52840DK, I can send data over a UART into it and I can get data out which is received...
Hi Community,
I made a custom board based on thingy53, created a similar custom board file folder.
The application code can be compiled correctly with the original thingy53...
I am using NRF Connect for VS Code on Ubuntu 24.02 with an adafruit nrf52840 feather express. When attempting to use the DeviceTree Extension, the wrong dts file is listed...
Hello,
We are using the npm1300 with a battery with an NTC.
Can we add a ferrite between battery NTC and npm1300 NTC?
Note: there is an error in our design we will...
I have managed to get, somehow, a central_uart talking to a peripheral_uart on a pair of 52840 DKs.
I've changed the UUIDs of what I'm trying to connect to, to be those...
Hello!
I built the https sample app for the Sparkfun_I got run time errors.
my setup:
Updated Windows 11 Pro
SDK 2.6.1 and 2.8.0
How do I solve this?
"The Modem...
Hi,
I am using a Proteus-e module from Wurth Elektronik for a project. This module contains a nRF52805 chip. I am using the nRF Connect app to send commands to configure...
Hello.
I'm trying to enable MCUBOOT in my project.
I added CONFIG_BOOTLOADER_MCUBOOT=y to the prj.conf, but I'm getting the next message: " BOOTLOADER_MCUBOOT set more...
